Don't know yet bud, too busy makin sure the main truggy is ready for ACT....will look when get back.

Yes that big double was interesting with that strong head wind :eek:

went to massive mods yesterday and got myself a .21 pullstart go tech.
it was missing the pullstart pin and mark was kind enough to pull one out of a different motor to send me on my way :nod:

can anyone recommend glow plug for the .21 3 port pullstart motor?
mark was out of go tech plugs. :lol:

I think it's a standard style plug, not turbo.

Any brand with a medium heat range would be good.

I think I used to use a standard OS #5 or #8, been so long I'v forgotten thou.

If its a turbo, try the Odonnel T97

lets bump this thread

http://i369.photobucket.com/albums/o...8/IMG_0986.jpg

hey guys, the 0.21 pullstart won't fit onto my D8 buggy, the pullstart touches the top engine mount and i don't think i can dremel as its where the pullstart comes out of the plastic case.

is there a back plate i can get for this motor to use a bump box instead?

thanks.

I would assume so, the .21 comes in bump start, so I'd say it's easy to get a back plate for it.

Phone or e mail Massive

kai888 - you will need the following parts for the backplate conversion on your .21 Sport motor:

Rear cover for .21, .25, .28 RTR - Part # 28-1000
O Ring AS-018 - Part # OR-0027
Screw 2.6 x 6 (4 pce) - Part # S6-2606

You will need the screws as the pull start screws will be too long in the thread for the backplate.

Cheers :cool:

Lookin good Flanno :sneaky:

Hows this one then ?

http://i369.photobucket.com/albums/o...s/IMG_1892.jpg

And side view

http://i369.photobucket.com/albums/o...s/IMG_1164.jpg

Ye haa, look at those tyres in the first clip - and i've got dim wits over here trying to tell me the MG66 will lack bottom end in a truggy - NOT!!!!!

Just point em to this thread buddy :nod: or the other one in the off road section with all the vids I posted :D

http://i369.photobucket.com/albums/o...s/IMG_1912.jpg

August 2009 ACT states ( yellow/red and white "BCE MBX5T

http://www.youtube.com/watch?v=5OLOdoYbDUs



Janruary 2010 Maitland/Newcastle (Same as next lot of clips but clearer so ya know what car to look out for, starts filming me at 1min 20ish

http://www.youtube.com/watch?v=F7ScmRZJewc

December 2009 Tasmania (Yellow/red and white with yellow wing. :"not the yellow with black wing." see the previous clip to get to know the car colours.

http://www.youtube.com/watch?v=Vud56Td6VZA

http://www.youtube.com/watch?v=88Ht_...eature=related

http://www.youtube.com/watch?v=jXgwY...eature=related


May 2010 NSW State tittles. (Yellow/red and white with white wing.

http://www.youtube.com/watch?v=kIqaAgfEY1k


August 2010 Australian nationals (Flame front and pink/white with white wing

http://www.youtube.com/watch?v=BucFOIkwSsc

:nod:Thats the stuff Flano :sneaky:
Might make a few of them NZ guys think again hey Grizz ;) (Gday NZ guys:D)

RIP my old 7 port today :( near 30ltrs through it on the original P/R/S and bearings and the rod finally let go, yeah I know...should have changed some parts before but I wanted to see how long she would GO for:lol::weird:
Time know for my favorite fix :confused: same piston/sleeve GX rod and a MG66 crank, done one of these already, works OK ya reckon:lol::nod:

:ha:

http://i824.photobucket.com/albums/z...ofDSCF5842.jpg

thank god for moulded foams, if ya had the old style in there the fronts would be stuffed now:tire::lol:

thanks guys, i think i'm just going to remove that rod connecting the pullstart and just cut up the pullstart, no point in spending more money on this motor :lol: