|
Originally Posted by kai888
(Post 7987834)
thanks guys, i think i'm just going to remove that rod connecting the pullstart and just cut up the pullstart, no point in spending more money on this motor :lol:
The backplate kit should only be around $25 - $30 tops I would think in $AUS |
Originally Posted by grizz1
(Post 7985786)
kai888 - you will need the following parts for the backplate conversion on your .21 Sport motor:
Rear cover for .21, .25, .28 RTR - Part # 28-1000 O Ring AS-018 - Part # OR-0027 Screw 2.6 x 6 (4 pce) - Part # S6-2606 You will need the screws as the pull start screws will be too long in the thread for the backplate. Cheers :cool: I assume the rear cover is like a MG66 cover , same part number ? |
Originally Posted by Flanno
(Post 7989851)
I assume the rear cover is like a MG66 cover , same part number ?
These are alloy coloured, not black. Biggest difference is they have a groove cut in the inner face that makes room for the little pin on the end of the actual crank pin (that fits into the pullstart shaft) to pass through the back plate as the crank spins. I am guessing a normal GX backplate might fit if you ground the pull start pin off the crank, but probably easier to get the proper back plate ? |
Originally Posted by grizz1
(Post 7990146)
Na she's different Flanno. MG is Part# 21-1005-M2
These are alloy coloured, not black. Biggest difference is they have a groove cut in the inner face that makes room for the little pin on the end of the actual crank pin (that fits into the pullstart shaft) to pass through the back plate as the crank spins. I am guessing a normal GX backplate might fit if you ground the pull start pin off the crank, but probably easier to get the proper back plate ? |
We heard on the weekend that Massive was going up for sale, is this correct?
Wasnt a bs artist source either.. |
Originally Posted by Flanno
(Post 7990366)
Oh bummer, I had a spare he could have had.
thanks again mate. |
Originally Posted by Dr freedom
(Post 7990897)
We heard on the weekend that Massive was going up for sale, is this correct?
Wasnt a bs artist source either.. |
there you go .. chinese wispers
|
dam, i thought he might move the shop to budgewoi :lol::lol::lol:
|
Originally Posted by Dr freedom
(Post 7991593)
there you go .. chinese wispers
|
Originally Posted by Flanno
(Post 7987785)
thank god for moulded foams, if ya had the old style in there the fronts would be stuffed now:tire::lol:
|
Originally Posted by Dr freedom
(Post 7990897)
We heard on the weekend that Massive was going up for sale, is this correct?
Wasnt a bs artist source either..
Originally Posted by kai888
(Post 7991262)
no worries flanno, very grateful that you even offered in the first place :nod:
thanks again mate.
Originally Posted by kai888
(Post 7991282)
when i went there a few weeks ago, mark said his moving his shop to liverpool?
Originally Posted by Dr freedom
(Post 7991593)
there you go .. chinese wispers
|
That's funny. I heard he was going international and shifting trans-tasman to Auckland :D
Somewhere in a suburb called Titirangi. Sounded like it might have been next door to me !! :lol: :lol: |
Not likely Grizz, he'd never get any work done as you'd be next door bending his ear all day :lol:
|
Originally Posted by Flanno
(Post 7994394)
Not likely Grizz, he'd never get any work done as you'd be next door bending his ear all day :lol:
Our 3 day Nationals are starting on Friday. Brand new track that nobody has had a buggy on. Should be a good weekend :nod: |
| All times are GMT -7. It is currently 08:00 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.