BMI Racing Discussions
#9676
Tech Rookie
Originally Posted by DENNIS STORTI
Dont hold me too this im just telling you what i have seen
chassis,topdeck,f/r towers,rear bulkhead brace,standoffs, and i think he is making another brace for the rear bulkheads that will be seperate.
Hope that helps
chassis,topdeck,f/r towers,rear bulkhead brace,standoffs, and i think he is making another brace for the rear bulkheads that will be seperate.
Hope that helps
re:stand-offs...the factory cyclone doesn't appear to have standoffs. any ideas what BMI does-away with from the factory car?
#9677
dennis is correct. i didnt lose anything from the stock cyclone when i did this kit.i had to be pretty creative to do the wide bracing and make it look good.looks like the whole hot bodies team may run the chassis at the IIC race.andy moore just got his yesterday.
#9678
who is actually running damper tubes on your 12??
#9679
Originally Posted by Mason
who is actually running damper tubes on your 12??
#9680
which tubes and what thread size studs are you using? i have a load of crc stuff and the holes in the cf are too large to thread directly into with crc 2-56 ball studs. is there a longer stud out there? is it 3-56, 3-48 instead?
#9681
Originally Posted by Mason
which tubes and what thread size studs are you using? i have a load of crc stuff and the holes in the cf are too large to thread directly into with crc 2-56 ball studs. is there a longer stud out there? is it 3-56, 3-48 instead?
hardware 1384 - 2-56 Steel Ballstud for tubes
tubes 1369 - Short Alum Damper Tube
#9682
i believe i have those same parts. i'll triple check when i get home. on all 3 of mid decks and the 1 top plate i have, the ball studs slide in and out like its at a nevada brothel and they are too short to nut on the bottom side.
#9683
i have not had a problem with those part. but i am just now putting the db12 together. I beleive that the tbrace is the same as the original bmi12 so they should work. I did have to counter siink the ball stud on the top deck for the pod. crc use to have the same hardware kit and included the long studs. but I have not been able to find those anymore.
#9684
Tech Rookie
Originally Posted by protc3
dennis is correct. i didnt lose anything from the stock cyclone when i did this kit.i had to be pretty creative to do the wide bracing and make it look good.looks like the whole hot bodies team may run the chassis at the IIC race.andy moore just got his yesterday.
Any photo's of the kit?
#9686
Super Moderator
iTrader: (239)
Originally Posted by protc3
dennis is correct. i didnt lose anything from the stock cyclone when i did this kit.i had to be pretty creative to do the wide bracing and make it look good.looks like the whole hot bodies team may run the chassis at the IIC race.andy moore just got his yesterday.
#9687
Tech Rookie
Originally Posted by mintygreen
Sweet as ! You know BMI's does the best chassis when the factory team...don't run factory chassis !
Any photo's of the kit?
Any photo's of the kit?
Last edited by mintygreen; 09-22-2006 at 02:10 AM.
#9688
hey guys,
i got a call last night and was told that andy moore and a few of the HB team were changing over to the new BMI Cyclone carpet kits!!! best of luck to them.
Jason Schreffler is on fire right now with his BMI Cyclone.i have a real good feeling about the results.
i got a call last night and was told that andy moore and a few of the HB team were changing over to the new BMI Cyclone carpet kits!!! best of luck to them.
Jason Schreffler is on fire right now with his BMI Cyclone.i have a real good feeling about the results.
#9689
Thats great news.
#9690
jason, ygm