867LikesTamiya Euro Truck Class
08-03-2022, 11:13 AM
#1486
08-03-2022, 11:24 AM
#1487
just measuring by my uncalibrated hands
no. It doesn't feel as tight with the grease as it did with the 100k.
The truck has better drive with the grease in the rear(to me), but this was also on black carpet. Fortunately it's not to hard to pull the diff and try different things during a practice session. That's what I did when it was suggested to me to try the red and tacky.
no. It doesn't feel as tight with the grease as it did with the 100k. The truck has better drive with the grease in the rear(to me), but this was also on black carpet. Fortunately it's not to hard to pull the diff and try different things during a practice session. That's what I did when it was suggested to me to try the red and tacky.
08-03-2022, 12:42 PM
#1488
https://www.teamgravityrc.com/online...lion-p56979859
use that in the front and a small amount of Tamiya anti wear grease in the rear
use that in the front and a small amount of Tamiya anti wear grease in the rear
08-10-2022, 11:33 AM
#1489
Are we allowed to run BECs for the servo? I don't see any mention of them not being allowed in the rules.
https://www.tamiyausa.com/tcs/rules/...47uHEvpuKpxOU4
I wanted to run a CC BEC 1.0 at 8.4v but not sure if that's acceptable.
https://www.tamiyausa.com/tcs/rules/...47uHEvpuKpxOU4
I wanted to run a CC BEC 1.0 at 8.4v but not sure if that's acceptable.
08-10-2022, 12:37 PM
#1490
Are we allowed to run BECs for the servo? I don't see any mention of them not being allowed in the rules.
https://www.tamiyausa.com/tcs/rules/...47uHEvpuKpxOU4
I wanted to run a CC BEC 1.0 at 8.4v but not sure if that's acceptable.
https://www.tamiyausa.com/tcs/rules/...47uHEvpuKpxOU4
I wanted to run a CC BEC 1.0 at 8.4v but not sure if that's acceptable.
08-12-2022, 08:40 PM
#1491
Tech Apprentice
Coca-Cola Express
Finally completed and ran up at my local track Indy RC tonight.
08-13-2022, 05:44 AM
#1492
It looks really sharp! Great job on that scheme!👍🏻
08-14-2022, 12:23 PM
#1494
The "McTruck" ran at Indy RC Raceway this past Friday night and won the A-main. It looks even better in person.
This was the first race night ever for the top 2 trucks and both were very close in performance. It has been a while since we have raced Euro Trucks at this track, but overall the night was a fun success. All the trucks racing did have a little bit of super glue on the outside edge of the front tires which does help reduce over-steering/traction rolling in this class.
Check out the results here...
https://indyrc.liverc.com/results/?p...vent&id=384168
or video here...
This was the first race night ever for the top 2 trucks and both were very close in performance. It has been a while since we have raced Euro Trucks at this track, but overall the night was a fun success. All the trucks racing did have a little bit of super glue on the outside edge of the front tires which does help reduce over-steering/traction rolling in this class.
Check out the results here...
https://indyrc.liverc.com/results/?p...vent&id=384168
or video here...
08-15-2022, 11:01 AM
#1495
Tech Apprentice
TCS Compliant
I was running TCS rules to the letter, the chassis with the truck body is about as fast as you’d want to go on the smaller track. It was a bit tipsy…
08-20-2022, 04:32 PM
#1497
These trucks look like so much fun! Every time I come out on these forums I find new stuff I want to build.
08-22-2022, 07:11 AM
#1499
Tech Apprentice
Euro Truck Lipo
What are some rounded case lipos available that are legal for TCS Euro Truck Rules?
08-22-2022, 08:31 AM
#1500