new ofna DM1 pics and thoughts :):)
#1306
Tech Master
iTrader: (70)
Mark,
I pitted for RV and he carved your DM1 around LH track like it was on rails!
Of course he is a wheel but the car looked great!
You do great work on these cars!!
I would have like to have seen him with an open motor in it!!!
Happy to haul it up there for him.
Cya soon.
-Jonny Boy
I pitted for RV and he carved your DM1 around LH track like it was on rails!
Of course he is a wheel but the car looked great!
You do great work on these cars!!
I would have like to have seen him with an open motor in it!!!
Happy to haul it up there for him.
Cya soon.
-Jonny Boy
#1308
Tech Champion
iTrader: (17)
Well, I guess the best offer I can give you is to send the car and all your parts to me and I'll get it built and ready for the next run. Car would show up just like what I sent to Rick with parts that you may need. You get the body ready, if it comes with the engine, I'll have the clutch set up. You pay for the parts and labor is on me. ........
Just have to run it as it is, no changes unless done by the "Approved Team".
I know it would have been better if I had been there, but work got in the way ......
Just have to run it as it is, no changes unless done by the "Approved Team".
I know it would have been better if I had been there, but work got in the way ......
Sorry I cannot use your conversion and finish the race......but with those short 5 minutes run when the diff was fine, car is DAILED.........just as good as RV.
#1309
Tech Master
iTrader: (70)
MWS Racine might be my last stop for this year.........let me think about it or I will ship that over to you for the turn key service. You know me...I am the driver, I don't deal with service...LOL.
Sorry I cannot use your conversion and finish the race......but with those short 5 minutes run when the diff was fine, car is DAILED.........just as good as RV.
Sorry I cannot use your conversion and finish the race......but with those short 5 minutes run when the diff was fine, car is DAILED.........just as good as RV.
#1311
Tech Master
iTrader: (70)
Hey Mark,
Here is a pic of one of the bumpers that I purchased from you fitted to an
Ofna McClaren body. Great firm bumper!
I will post another pic of another fitted to an Alpha body when I have it completed. Might be a bit though as Wang "stole" my first rendition! lol.
Thanks for a great product!!!
Here is a pic of one of the bumpers that I purchased from you fitted to an
Ofna McClaren body. Great firm bumper!
I will post another pic of another fitted to an Alpha body when I have it completed. Might be a bit though as Wang "stole" my first rendition! lol.
Thanks for a great product!!!
#1312
Tech Elite
iTrader: (40)
Hey Mark,
Here is a pic of one of the bumpers that I purchased from you fitted to an
Ofna McClaren body. Great firm bumper!
I will post another pic of another fitted to an Alpha body when I have it completed. Might be a bit though as Wang "stole" my first rendition! lol.
Thanks for a great product!!!
Here is a pic of one of the bumpers that I purchased from you fitted to an
Ofna McClaren body. Great firm bumper!
I will post another pic of another fitted to an Alpha body when I have it completed. Might be a bit though as Wang "stole" my first rendition! lol.
Thanks for a great product!!!
Mark
#1318
Tech Initiate
Hey everyone. I've been checking out the DM1 Pro on Amain's site for quite some time now, but was a little put off to buy it being I can't seem to find spares for it. It's apparently compatible with other OFNA/ Jammin cars. Does anyone know which buggies/ truggies it's compatible with? Also, will the 1/8 DM1 Spec E's single speed center spool fit?
After reading through just about every post on her today, it seems like you guys have a fair amount of sources for parts. Is there a link thread for this car? Thank in advance.
After reading through just about every post on her today, it seems like you guys have a fair amount of sources for parts. Is there a link thread for this car? Thank in advance.
#1319
Tech Initiate
How much were you looking at for the NIB one?
Finally got to run my DM-1 with some decent tires.. Proline Road Rage SC tires (I think) on DE Racing 17mm rims.. Awesome grip. Was able to push the car so much harder than I'd ever been able to before(on a non-groomed asphault mess-around track where I run it mostly..)
All those stupid small-diameter rally game tires I bought are freakin' useless (for a non-racer like me especially..)
I've been trying to sell my two 7th scale DM-1's for a while now, with no bites. And I'm not going to give them away. One is used, the other still unassembled in the box. So I guess - especially now that I know what tires are decent - I'm going to be keeping them for the long run. Just need to be sure I can buy clutch bells(the annoying Achilles heal of the DM-1 IMO, the rest of the car being awesome..) and 2-speed parts in the future... I guess CB's are fewer and further between these days. So if anybody knows of a good source, lemme' know. Nitrohouse is useless to me, as they want 30 bucks shipping for whatever you order, however small...
All those stupid small-diameter rally game tires I bought are freakin' useless (for a non-racer like me especially..)
I've been trying to sell my two 7th scale DM-1's for a while now, with no bites. And I'm not going to give them away. One is used, the other still unassembled in the box. So I guess - especially now that I know what tires are decent - I'm going to be keeping them for the long run. Just need to be sure I can buy clutch bells(the annoying Achilles heal of the DM-1 IMO, the rest of the car being awesome..) and 2-speed parts in the future... I guess CB's are fewer and further between these days. So if anybody knows of a good source, lemme' know. Nitrohouse is useless to me, as they want 30 bucks shipping for whatever you order, however small...