Grenade10

Tech Elite

Last Activity: 04-15-2023 05:55 AM

About Me

About Grenade10

Biography

1/12 On Road Racing, 1/8 Scale Gass

Location

Fort Collins, Colorado

Interests

R/C Cars, Models

Occupation

Construction
Signature
Darkside, Sweep, BSR, Fantom, IGT Hobbies and IGT8
Byrons Fuel, ProtoForm Bodies & Futaba Radio Gear by Choice
Founding Member of CORRC .... 5280raceway
www.darksidems.com www.igthobbies.com www.IGT8.com

Statistics

Total Posts

Total Posts: 4,737
Posts Per Day: 0.66
Find all posts by Grenade10
Find all threads started by Grenade10

Visitor Messages

Total Messages: 25
Most Recent Message: 06-16-2021 04:57 AM
Visitor Messages for Grenade10

General Information

Last Activity: 04-15-2023 05:55 AM
Join Date: 11-06-2003
Referrals: 0

Friends

Showing Friends 1 to 4 of 4

- *1speedy
- Tech Fanatic
- chaderick
- Tech Adept
- MIKE HINDS
- Tech Regular
- Scottrik
- Tech Champion

Visitor Messages

Showing Visitor Messages 1 to 10 of 25

06-16-2021 04:57 AM - permalink

terencengan

Hi, the wheel for Serpent still available?
808815 Front wheels neon yellow BBS (2)
08845 Rear wheels neon yellow BBS (2)
and i saw your message said you have some already mounted with tires ?
- View Conversation
05-15-2016 01:51 PM - permalink

ChadBlanton

Grenade, I'd really like to experiment with different springs. Can you tell me what springs will fit and what spring rates are stock to the IGT8 as a starting point.
- View Conversation
12-28-2015 01:20 PM - permalink

bigjez

Ok thanks i wanted to buy x3gt-igt8 but i seen no one carries parts for it hardly.I will sit back and wathc for a while and decide then thanks for the reply.
- View Conversation
12-19-2015 05:37 AM - permalink

bigjez

hello I have been following gt8 for awhile now and I have a few questions if you don't mine.
1st I have a dm-1 I got it used but never ran due to work and kids. what made this car out of date outside of parts I see gt8 cars now around the same weight now. and comparing your igt8 to your dm-1 how much faster is it?
I also noticed a lot of gripe on the dm-1 pivot ball a arms and now mugen is out .is there an advantage with the pivot ball arms?

Over all is it the progression and learning curve in the tunning and or is the motors that make the serpent,mugen,igt8 faster then the dm-1 thanks in advance.
- View Conversation
11-09-2015 07:37 AM - permalink

Jeff burns

Hello I am interested in the ofna gear part #35249 49t. My name is Jeff burns email is [email protected] phone #518-370-6138.
- View Conversation
08-18-2015 07:32 PM - permalink

qaberdeen

Grenade.. I have a quick question for u.. I'm currently building my IGT8 and i'm currently stuck on the servo saver.. are there suppose to be 4 bearings for the two post.. I see that I have 3 plastic shape spacers that fits perfect but I don't see the bearings any where and I only have 3 plastic spacers instead of 4, but I m pretty sure I should have servo saver bearings..thks agin Q
- View Conversation
04-28-2015 05:42 PM - permalink

nitrobadass

I'm in trouble... I'm registered in R/C Tech now...
My address is

Patrick Werner
217 South 4th
Seward, NE. 68434
- View Conversation
04-08-2015 10:35 PM - permalink

c00lguy

Hello. Are the Kyosho GT2/DM-1 Parts still available? I am interested. Thanks
- View Conversation
01-11-2015 10:38 PM - permalink

FABIO1964

Hi Grenade10
I was looking again at the thread and found your quote
"Use 3 or 4 bearing in the front of the clutch bell. PM if you have questions."
Do you mean to say I need to purchase additional bearings to fill-up all the space up to the to, flush with the bell? I presume I will need a longer screw then.
Thanks for your advice on this.
Fabio
- View Conversation
03-14-2014 01:11 PM - permalink

turndownwhip

yes! please send on to [email protected]
- View Conversation