Xray NT1
#6346
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
XRAY Released NT1 PRO Ver.
#6347
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Go softer on the clutch and lighter on the front diff oil. Such a heavy oil pulls the front like crazy on power.
Try something like 100 front and 60 rear to start and tune from there.
[QUOTE=JamesHealey;11032526]Ran the NT1 yesteday, struggled with an on power over steer on corner exit.
Couldn't apply the throttle leaving the corner all day.
Try something like 100 front and 60 rear to start and tune from there.
[QUOTE=JamesHealey;11032526]Ran the NT1 yesteday, struggled with an on power over steer on corner exit.
Couldn't apply the throttle leaving the corner all day.
#6350
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
why and where would you use progressive springs ?
#6352
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Xray Releasd la !!
#6353
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Is anyone using the conical spring washers in the High dynamic clutch ?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
#6354
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Is anyone using the conical spring washers in the High dynamic clutch ?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
#6355
Tech Initiate
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm running .5 gap and about the same .5 on the adjusting nut. Lots of punch out of turns. Start at about .4-.5 on the nut and tighten if needed.
Is anyone using the conical spring washers in the High dynamic clutch ?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
i set mine up as per the booklet with the 5 x big washers in first then followed by the 5 thin washers and setting the adj nut to 1mm. i started with a .6 gap and the clutch was slipping pretty bad.
what are peoples thoughts on the washers and what setup are you using?
#6357
#6359
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm not sure if this applies. I ran the conical washers in a Serpent clutch (sedan) with a red shoe which is a softer shoe and it was beautiful. I would run a small gap maybe .3mm -.5mm. I would believe the conical washers do not have as much throw as a spring setup.
Pass you soon...
Pass you soon...
#6360
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I'm not sure if this applies. I ran the conical washers in a Serpent clutch (sedan) with a red shoe which is a softer shoe and it was beautiful. I would run a small gap maybe .3mm -.5mm. I would believe the conical washers do not have as much throw as a spring setup.
Pass you soon...
Pass you soon...
![Stick Out Tongue](https://www.rctech.net/forum/classic_images/smilies/tongue.gif)