Viper RC -
#3976
#3978
#3980
Tech Master
iTrader: (11)
The straight is about 110ish feet, I will be trying to gear down this weekend to see what happens. I know that the fastest (top end) on the track is running the same gearing with a different motor. I have been told to keep going bigger with the viper stuff. I think I am going to back down to like 30/75 and work my way back up. The one thing I do have to say is that even with the big ratio I have, my viper gear is NOT having any torque issues! Bottom end on these motors is stout.
The enemy in 17.5 is heat. The VST17.5 has substantial torque and is capable of pulling some serious gear, for 2 or 3 minutes. The heat will eventually slow the motor and cook it. We have to either limit the gearing and/or the timing to controll temps.
That is the reason why you are seeing your new motors have all sorts of slots and holes to allow the heat out.
And you can temp the outside of motors with the best heat guns, but it is a very in-accurate measurement of the motor. You can get the stator to change temp by 20 or 30 degrees and it will only show a 2-5 deg temp change on the outside of the motor. The difference between 130-140 on the outside of the motor may be as much as a 50 or 60 degree temp change internally depending on how "fast" the motor was heated up.
#3981
Tech Rookie
I just didnt know why it did it early, then ran fine for a heat, then did it twice in a row (after 2-3 minutes). I dont have enough run time on it to know if the 13 has made it stop completely or not. I'll run again in a couple of weekends with the 13 and see what happens I guess.
#3982
any due dates for the vse 1/8 motors yet?
thanz
thanz
#3984
Tech Adept
iTrader: (50)
540 they say no limit. Yes but as was stated by several people that statment was describing 2pole 540 motors.
The pro4 is very new and is a differnt animal. That speed control was designed before the release of the 4 pole Pro4. The pro4 draws power like a 1 to 2 turn 550 motor but in a 540 can.
Good luck. all I can say is you have been warned.
Maybe you could post your testing of this so others with the same question could search and find their answer?
The pro4 is very new and is a differnt animal. That speed control was designed before the release of the 4 pole Pro4. The pro4 draws power like a 1 to 2 turn 550 motor but in a 540 can.
Good luck. all I can say is you have been warned.
Maybe you could post your testing of this so others with the same question could search and find their answer?
#3985
Tech Master
iTrader: (11)
540 they say no limit. Yes but as was stated by several people that statment was describing 2pole 540 motors.
The pro4 is very new and is a differnt animal. That speed control was designed before the release of the 4 pole Pro4. The pro4 draws power like a 1 to 2 turn 550 motor but in a 540 can.
Good luck. all I can say is you have been warned.
Maybe you could post your testing of this so others with the same question could search and find their answer?
The pro4 is very new and is a differnt animal. That speed control was designed before the release of the 4 pole Pro4. The pro4 draws power like a 1 to 2 turn 550 motor but in a 540 can.
Good luck. all I can say is you have been warned.
Maybe you could post your testing of this so others with the same question could search and find their answer?
The VTX10R will run some, but will severely cog with hard acceleration. We do not recommend this configuration at all.
The Pro4 motor is basically a short 1/8th scale motor.
#3986
Tech Elite
iTrader: (270)
Copper head
OK Guys maybe someone can help me filled out the warranty form on Viper site to return my copper head motor, It says i will be getting a email i have seen nothing yet? Iam i missing something? Love the systems just trying to get it replaced asap so i can run it again!