|
Originally Posted by bkspeedo
(Post 9800034)
I am running a 3.8 FDR but my other ESC's work fine with this FDR. This other ESC had the same problem in the beginning and it took them quite some time to fix it.
Hopefully the Hobbywing group can figure it out sooner than later. |
Originally Posted by mingnon
(Post 9799671)
I prefer to use drag brake, dont know why, just fits my driving style. Having changed to the hobbywing esc, it isnt and strong as others. Me personaly, would prefer it to be more effective and adjustable
|
Isn't drag brake a percentage of the full brake force? I thought I read that somewhere and I will do a test to confirm it.
I just loaded the new v3 stock software into my ESC and set the drag brake to my previous value. It was much more effective and I reduced my setting from 30% to 15%. I am running the 4 capacitors though. |
211 vs 930 stock
Hi guys
Just a quick question. I have been running 211stock software and have just changed to 930 stock. What differences will I feel when running the same settings? Anything? Cheers |
Originally Posted by Barry_Hughes
(Post 9801018)
Drag barake force is adjustable second step of programming
|
need a setup for xtremestock with speed passion 17.5 boosted ASAP!
indoor carpet, small to medium size track |
I have a problem with my extreme stock ESC , it won't run unless it is given a push first, then it will run until it comes to a complete stop
I have changed motors and sensor leads and the problem is still there, have even re flashed speedy Any suggestions |
Originally Posted by lethallee69
(Post 9803187)
I have a problem with my extreme stock ESC , it won't run unless it is given a push first, then it will run until it comes to a complete stop
I have changed motors and sensor leads and the problem is still there, have even re flashed speedy Any suggestions |
Originally Posted by lethallee69
(Post 9803187)
I have a problem with my extreme stock ESC , it won't run unless it is given a push first, then it will run until it comes to a complete stop
I have changed motors and sensor leads and the problem is still there, have even re flashed speedy Any suggestions Along with Angelo's comments it may be a bad sensor wire or board in the motor. It either of these are bad it will try running in sensor-less mode. With high wind motors the ESC has a hard time starting the motor due to not enough feedback from the motor coils. |
Originally Posted by bkspeedo
(Post 9804153)
Along with Angelo's comments it may be a bad sensor wire or board in the motor. It either of these are bad it will try running in sensor-less mode. With high wind motors the ESC has a hard time starting the motor due to not enough feedback from the motor coils.
|
Originally Posted by lethallee69
(Post 9805401)
Have tried different motors and sensor cables, it still runs with boost mode it's just that it won't take off without a push first
|
Originally Posted by lethallee69
(Post 9805401)
Have tried different motors and sensor cables, it still runs with boost mode it's just that it won't take off without a push first
|
Originally Posted by lethallee69
(Post 9805401)
Have tried different motors and sensor cables, it still runs with boost mode it's just that it won't take off without a push first
|
Originally Posted by lethallee69
(Post 9803187)
I have a problem with my extreme stock ESC , it won't run unless it is given a push first, then it will run until it comes to a complete stop
I have changed motors and sensor leads and the problem is still there, have even re flashed speedy Any suggestions |
Tried the V3 no timing on the Just Stock last night. Couldn't tell if the brakes were stronger. My lap times are the same but the temp went down 20F. Really happy with the update. Good job.
|
| All times are GMT -7. It is currently 07:17 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.