|
http://rcmarket.com.hk/product_info....oducts_id=8065
that the wire for aitronic/sanwa rx for m11x!! |
DSC
Has anyone used the DSC wire? Where can I purchase it?
|
...is any one running the RX451 with a 7.4v lipo rx hump pack plugged directly into it? Reason im asking is that the input voltage is 6v and lipos can be as high as 8.4v when fully charged. Will I fry it or is it safe to do??
...or must a 6v lipo regulator be used? please let me know. Install is going into an rc boat, one 1/4 scale servo and one standard sized. |
man read the page before and you will find the answser!
|
...ive read it mate but its not that clear. A simple yes or no answer would be great to avoid me frying the rx if it wont work. Some say yes others say they use the 451R which is made to support lipos.
Will the 451 be okay with a lipo plugged directly into it? |
Originally Posted by exotica
(Post 7850033)
...ive read it mate but its not that clear. A simple yes or no answer would be great to avoid me frying the rx if it wont work. Some say yes others say they use the 451R which is made to support lipos.
Will the 451 be okay with a lipo plugged directly into it? |
Originally Posted by exotica
(Post 7850033)
...ive read it mate but its not that clear. A simple yes or no answer would be great to avoid me frying the rx if it wont work. Some say yes others say they use the 451R which is made to support lipos.
Will the 451 be okay with a lipo plugged directly into it? yes its fine i have emailed airtronics and they gave me the confirmation |
Originally Posted by mhavlena
(Post 7809552)
Guys:
Had a bad experience this weekend where my new M11X seemed to loose its bind during a race. Receiver Batt was freshly charged, well, 1 day earlier. I lost control of the car. One I checked the Receiver, the blue light was blinking??? I'm assuming this meant that the bind was lost... Has anyone experienced this? Do I have a defective unit?? Awaiting for your replies!!! Thx!!! totally lost control of my car, She was going round n round in circles. And the blue light was blinking. I've since tried to rebind, but nothing. Its' like it all most binds then nothing. :( |
my son had the same problem he got it to bind but if it does it again i`m going to send it in
|
compatibility...
have some questions... does the new digital brushless servo work with the older receivers rx441ds (but of course not in the 2.5 ms response time) ?
also for the new receiver rx451 (no r), does it work with the older servos vz-b, vz, rz ? many thanks :cool: |
Originally Posted by mrbusta
(Post 7852832)
yes its fine i have emailed airtronics and they gave me the confirmation
Still waiting for Sanwa to replace them (only been 4 months). We switched to LIFE and we had no more problems. The lipo's were a 2,200 2 cell. Cheers Mark |
Hey guys, just acquired a lipo for my Tx. I remember reading somewhere that you can plug a lipo in only one certain direction. I don't want to fry the transmitter, which way can i plug it in?
|
Originally Posted by Mr. Bojangles
(Post 7908113)
Hey guys, just acquired a lipo for my Tx. I remember reading somewhere that you can plug a lipo in only one certain direction. I don't want to fry the transmitter, which way can i plug it
in? |
Hi all, i just bought an M11x, great radio so far! :D
Just one question regarding channel mode settings: i use the new 451-R receiver coupled with a Savox 1251mg digital servo on steering and a SP gt2.1 esc on throttle. Can i put the steering channel in SHR mode even if i don't use a Sanwa servo? Does anyone have experience with savox servos and 451-R receiver? Thanks! :cool: |
Fried original rx after i put a LiFe rx batt in for about 10 mins. switched back to nimh after the ten mins and ran it for bout 5 more mins. rx just died and she was gone....
|
| All times are GMT -7. It is currently 05:49 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.