1LikesPalmaris engine thread
02-02-2004 | 07:44 AM
#271
Originally posted by stefan
On a side note:
I just finished breaking in one of Edwards beryllium piston/sleeve/rod sets that I was planning to run at the Winternats. and that thing is very impressive.
Edward had it lapped to where it only took a very short break in time.
I started leaning it out and geeez... that engine is a bullet.
I installed the set in a Nova Mega (formerly 5 port) and prepared crank timing to Edwards recommendation.
If the P12 is even faster than that.........
I will not buy another Nova Rossi sleeve set as long as Edward's will be available.
On a side note:
I just finished breaking in one of Edwards beryllium piston/sleeve/rod sets that I was planning to run at the Winternats. and that thing is very impressive.
Edward had it lapped to where it only took a very short break in time.
I started leaning it out and geeez... that engine is a bullet.
I installed the set in a Nova Mega (formerly 5 port) and prepared crank timing to Edwards recommendation.
If the P12 is even faster than that.........
I will not buy another Nova Rossi sleeve set as long as Edward's will be available.
.Sets are available in any combination-AAC, BRB or ABC.
02-02-2004 | 09:15 AM
#276
Originally posted by Top Gun 777
Randy, ones I will come back from winternats, we will get one full day of running. but it will be on your unit.
Randy, ones I will come back from winternats, we will get one full day of running. but it will be on your unit.
02-02-2004 | 10:59 AM
#278
Originally posted by jwf_frani
TG good luck and have fun at Florida. As for testing i'm always
at Rev or CP if you need help.
TG good luck and have fun at Florida. As for testing i'm always
at Rev or CP if you need help.
I realy appretiate your offer for help in motor test and defenetly will use your driving skils and expirience for next testing
02-02-2004 | 02:31 PM
#279
Tech Fanatic
Joined: Nov 2003
Posts: 826
Originally posted by Corse-R
Uhm... seems that you're expanding on the fuel brewery and supplying to many people.... Should I expect to see you with a 55 Gallon drum of 30% fuel at the Wnats?
BTW: Please mail me the hotel address... this week will be quite busy for me and I'm finishing all the little details. Wanna try some very fine Enetti tyres? Will carry plenty of sets for 200mm (37, 40 & some 42's) and some for 1/8 (35 & some 37's).
Uhm... seems that you're expanding on the fuel brewery and supplying to many people.... Should I expect to see you with a 55 Gallon drum of 30% fuel at the Wnats?
BTW: Please mail me the hotel address... this week will be quite busy for me and I'm finishing all the little details. Wanna try some very fine Enetti tyres? Will carry plenty of sets for 200mm (37, 40 & some 42's) and some for 1/8 (35 & some 37's).
02-02-2004 | 02:50 PM
#280
Tech Addict
iTrader: (1)
Joined: Aug 2002
Posts: 602
head buttons
i was cleaning my mr12 motor and pico/onfa x12 and saw that the head buttons looked the same , started measuring and found that button height is the same head deck is the same ,head deck dia was 0.01 i got 13.78 mm nova and 13.79mm pico . anybody know if i could use the pico head button on my mr ???
02-02-2004 | 03:10 PM
#281
Tech Master
iTrader: (2)
Joined: Nov 2001
Posts: 1,219
From: TEXAS. USA
Edward
Good to hear that your P12 motor is running as good or even better then your expectations!!! The motor looks unique and should turn heads by its look and performance! 
Well, good luck to you and Team Palmaris at the Winternats.
BTW- dose the P12 weigh less then a norm sleeve motor?
Well, good luck to you and Team Palmaris at the Winternats.
BTW- dose the P12 weigh less then a norm sleeve motor?
02-02-2004 | 03:31 PM
#283
Re: Edward
Originally posted by PUNISHER
Good to hear that your P12 motor is running as good or even better then your expectations!!! The motor looks unique and should turn heads by its look and performance!
Well, good luck to you and Team Palmaris at the Winternats.
BTW- dose the P12 weigh less then a norm sleeve motor?
Good to hear that your P12 motor is running as good or even better then your expectations!!! The motor looks unique and should turn heads by its look and performance!
Well, good luck to you and Team Palmaris at the Winternats.
BTW- dose the P12 weigh less then a norm sleeve motor?
Thanks for wishing luck.
Motor weight is about the same as the rest of existing models. I got some weight saving on sleeve area ( lower down SG).
