![]() |
I should add that I have seen crankpin wear from dirt, shoe polish.... metal polish, chrome polish..lapping compound ( not mine obviously ) ....... Multiple times I have seen crankpins worn down before the engines were ever even fired....I guess guys decided to try using an abrasive compound and a drill to speed up the breakin...Needless to say the results weren't very good !
|
Originally Posted by Maximo
(Post 13162893)
I have never seen crankpin wear issues with Byron's 30/11 ! :nod:
Just figured i would put that out there for Byrons guys supporting this blend |
Has any tried using dirt bike air filter oil? If so, which brand?
|
I use motul and belray... There both Good!!! Just use a rag to clean the excess
|
I've been running Belray for over a decade. Great stuff.
|
Hi all I have a 28-7t and I have run 8 tanks thru 25% for run in,heat gun used to get temps right b4 starting this was a month ago the problem is that I've never been able to get on the throttle it just wants to die I have searched far and wide tried tuning it from a u tube tuning vid tried new turbo plugs still the same it just won't take off like I know it should so I thought I could ask here and see if any one can help me??i hope the motor is ok
|
Originally Posted by Camash
(Post 13163795)
Hi all I have a 28-7t and I have run 8 tanks thru 25% for run in,heat gun used to get temps right b4 starting this was a month ago the problem is that I've never been able to get on the throttle it just wants to die I have searched far and wide tried tuning it from a u tube tuning vid tried new turbo plugs still the same it just won't take off like I know it should so I thought I could ask here and see if any one can help me??i hope the motor is ok
|
Yeah I've leaned it (hsn) & lsn on the last tank of run in I drove around at 1/3 throttle when I went to give it a little bit more it just died no high rev b4 it just died so I leaned it a bit a bit more a bit more don't want to go too far tho funny thing is when it dies it starts straight back up no worries,man it's got me beat think I should maybe check the piston perhaps
|
Originally Posted by Camash
(Post 13163983)
Yeah I've leaned it (hsn) & lsn on the last tank of run in I drove around at 1/3 throttle when I went to give it a little bit more it just died no high rev b4 it just died so I leaned it a bit a bit more a bit more don't want to go too far tho funny thing is when it dies it starts straight back up no worries,man it's got me beat think I should maybe check the piston perhaps
|
Originally Posted by Maximo
(Post 13164030)
still sounds too rich...what fuel % are you using ?
|
I've been running moonshine brew for the last 6 years now (no broken conrods but two broken cranks :lol: (awfull STS and a nice Nosram)... and shortened lifespan on bearings when I ran pure synth oil). I found (thanks Monty and Novarossi) that you need approx. 3% castor in the fuel to get a good lifespan and no premature wear on engines.
I'll start running Byron again. For me, the Race 25/11 is great for practise, for drivers that whats a really long lifespan on their engines or for drivers that runs their engines too lean = too much oil. The Pro 25/9 is great for racing but your engine doesn't last as long as with 25/11. As Neal told me, you don't need to lean your engine as much to get it run clean with low oil percent as you do with higher oil percent fuel. I'll mix Pro and Race 50/50 to get the best of both fuels :nod: |
Has anybody here had any experience with the new Clio p5? I'm thinking about switching from O.S back to nova and thought I might give it a try
|
Clio Internals ! sorry guys no bypass ports !
|
haha
Originally Posted by Maximo
(Post 13165233)
|
I just recently switched from Byrons 30/9 to 30/8 race blend. I've been told the the 30/8 uses a different type of oil and actually lubricates better then 30/9. Can anyone alaborate on this?
|
| All times are GMT -7. It is currently 10:28 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.