![]() |
Originally Posted by air8
(Post 6193729)
Hi Monty, quick question. When you do the R2R break-in, are the engines run until "the nuts drop"? Or should I expect "the nuts too drop" some time soon? I should have asked you over the phone when I ordered the engine.
thanx chris i would have to charge alot more to run each engine 1.5 gallons which is usually around the area where this happens but the r2r is 3/4 to 1 gallon of fuel of a proper run in . i dont rev the engine out really hard during this time but usually tune the engine in good enough to run races ;) |
Ok sweet. I just didnt' know if I should expect it or not. Thanx man.
|
Hey Monty, on the P5X head buttons there are dimples. On my standard button there are 3 in a row and on the turbo's there is 2 on one side and 3 or 4 across from it. Do the 3 go over the exhaust port? Also, what is the reasoning for this? I was thinking it was for indexing the plug in the chamber but I'm not really sure. Thanks!
|
Originally Posted by 2fst2c
(Post 6197096)
Hey Monty, on the P5X head buttons there are dimples. On my standard button there are 3 in a row and on the turbo's there is 2 on one side and 3 or 4 across from it. Do the 3 go over the exhaust port? Also, what is the reasoning for this? I was thinking it was for indexing the plug in the chamber but I'm not really sure. Thanks!
|
Ok thanks!
|
plus 4
im getting a plus for and exhaust set ready to race!!!! Cant wait to get this engine and pretty much be ready to go to the track!!!!
|
Monty are you still finding the Nova 41005 ] header to work pretty good with a Dyn053 pipe?
|
Originally Posted by rockfordccinc
(Post 6206262)
im getting a plus for and exhaust set ready to race!!!! Cant wait to get this engine and pretty much be ready to go to the track!!!!
|
Originally Posted by air8
(Post 6206316)
Monty are you still finding the Nova 41005 ] header to work pretty good with a Dyn053 pipe?
|
Monty my mill showed up today and is in my 808 and ready to rock. Gonna run it bit tommorow to make sure it's good for the weather here. Thanks a bunch for the KILLER service! I'll be leaving a nice note on your site.
|
Originally Posted by slaytanic
(Post 6206575)
Monty my mill showed up today and is in my 808 and ready to rock. Gonna run it bit tommorow to make sure it's good for the weather here. Thanks a bunch for the KILLER service! I'll be leaving a nice note on your site.
enjoy , call if you need anything :D |
Originally Posted by houston
(Post 6193016)
j
try 3.5 turns out on low speed with barrel pulled out and 3.75 turns out on high speed on the older carbs |
Got a tank through the 21-5 this evening finally. After 10 minutes it temped 235-240. Wound out real nice without really pushing it too much. I felt "electric" smooth!:nod:
It's supposed to be 90's and hmuid as heck tomorrow. Any suggestions Monty? |
Originally Posted by slaytanic
(Post 6209572)
Got a tank through the 21-5 this evening finally. After 10 minutes it temped 235-240. Wound out real nice without really pushing it too much. I felt "electric" smooth!:nod:
It's supposed to be 90's and hmuid as heck tomorrow. Any suggestions Monty? what did you think of the engine :confused: |
Originally Posted by slaytanic
(Post 6209572)
Got a tank through the 21-5 this evening finally. After 10 minutes it temped 235-240. Wound out real nice without really pushing it too much. I felt "electric" smooth!:nod:
It's supposed to be 90's and hmuid as heck tomorrow. Any suggestions Monty? |
| All times are GMT -7. It is currently 12:12 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.