R/C Tech Forums - Houstons Engine Service H.E.S.

Page 586 of 595

« First

586

Show 40 post(s) from this thread on one page

R/C Tech Forums (https://www.rctech.net/forum/)

- Offroad Nitro Engine Forum (https://www.rctech.net/forum/offroad-nitro-engine-forum-157/)

- - Houstons Engine Service H.E.S. (https://www.rctech.net/forum/offroad-nitro-engine-forum/285444-houstons-engine-service-h-e-s.html)

Palebushman

06-29-2016 09:22 PM

Quote:

Originally Posted by THE PHILLY JYNX (Post 14584764)

Fellas..................ITS A JOKE!!!!!!!

I put the fried engine and boiled tyres on a plate........ Not even my dog would eat it! :ha::ha::D

:cry:

houston

07-19-2016 09:03 AM

Quote:

Originally Posted by Palebushman (Post 14585622)

I put the fried engine and boiled tyres on a plate........ Not even my dog would eat it! :ha::ha::D

:cry:

picky mutt ....:lol::tire:

EBMods

07-26-2016 01:06 PM

Braaaaap,Braaaaaaaaaaap

Hope you're doing well Monty, peace out homie.....braaap :nod::nod::nod:

houston

07-31-2016 08:12 PM

Quote:

Originally Posted by EBMods (Post 14614478)

Hope you're doing well Monty, peace out homie.....braaap :nod::nod::nod:

Im doin ....gettin better every day ....still a bit of healing to do forsure

sn47som1

08-06-2016 11:17 AM

Hey Monty I sent ya a pm did you get it?

jeromerc

09-04-2016 06:20 PM

Happy birthday Monty!

Palebushman

09-06-2016 01:00 AM

Happy Birthday from our neck of the woods here in Australia too Monty.

Hope you're fully recovered from your recent ailment. :tire::nod::tire:

.

houston

09-21-2016 01:46 PM

finally back to work and attended the first offroad race 8th scale since my surgeries

thanks for all the well wishes guys !!!:nod:

revo61

09-23-2016 10:24 AM

Quote:

Originally Posted by houston (Post 14678534)

finally back to work and attended the first offroad race 8th scale since my surgeries

thanks for all the well wishes guys !!!:nod:

Have fun!

jeromerc

09-23-2016 05:08 PM

Quote:

Originally Posted by houston (Post 14678534)

finally back to work and attended the first offroad race 8th scale since my surgeries

thanks for all the well wishes guys !!!:nod:

How is work going, are you like the safety guy or back to your old job?

Perrydog

09-26-2016 11:44 AM

Finally worn out my Fusion x5 in my truggy. What is recommended to freshen up? Just a pinch? Was considering getting it modded. Best jut to buy a new mill?

houston

09-26-2016 05:40 PM

Quote:

Originally Posted by Perrydog (Post 14683388)

Finally worn out my Fusion x5 in my truggy. What is recommended to freshen up? Just a pinch? Was considering getting it modded. Best jut to buy a new mill?

all depends perrydog

i have rebuilt quite a few and guys ran them for many gallons ... depends on what it needs for cost effectiveness

get a hold of me if you are looking for a new one

cczjordan

11-06-2016 05:51 AM

Does tko have the nova keep off 4 n 7 rear special ceramic bearings? If does, what is the part number

houston

11-10-2016 07:34 PM

14.5x26 offset

Quote:

Originally Posted by cczjordan (Post 14727020)

Does tko have the nova keep off 4 n 7 rear special ceramic bearings? If does, what is the part number

14x25.8 offset

cczjordan

11-11-2016 06:04 AM