Team Magic G4
#7921
hi everybody!!
i am alive!!
korea is a continuous rainy spell.
so i couldn't race frequenlty and there are no race event
i will back soon!!
and i am waiting TransG4ormer!!!! hodak!!
i am alive!!
korea is a continuous rainy spell.
so i couldn't race frequenlty and there are no race event
i will back soon!!
and i am waiting TransG4ormer!!!! hodak!!
#7922
Tech Adept
Hi everybody out there, hope someone can help me out with this.
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
#7925
Hi everybody out there, hope someone can help me out with this.
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
did you put thrust bearing grease in thrust bearing?
and.. i could clean the chassis by compressor in about 5 minutes.
#7926
Hi everybody out there, hope someone can help me out with this.
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
What could cause thrust bearing to brake almost on every race day?
Gear mesh is ok, i also try to adjust minimum endplay ~0.1mm, gap is ~0.5-0.6mm.
Black spring, red shoe, crf'07 engine, 52/47, 18/23 gearing
Btw, Gansei, how much time you spend to get chassis so clean?
1. bearing must be lubed with grease at least once on a club day or as well as before the mains.
2. run a smaller clutch gap of .4/.5mm, larger clutch gap is more aggressive.
The .1mm endplay is perfect and isnt teh problem.
Possible that you have clutch engaging a bit high and its stressing the thrust but i doubt it.
#7927
Tech Adept
Serpet bearing oil has been used for oiling, looks like i have to give a chance to standart thrust bearing grase.
#7928
You should put some prices up so people know what to expect to pay. You may get a few more bits this way.
#7929
#7930
Thrust bearing grease :
Mugen Seiki Super Grease
Tamiya AW Grease
Tamiya Molybdenum
Tamiya Ceramic Grease
Mugen Seiki Super Grease
Tamiya AW Grease
Tamiya Molybdenum
Tamiya Ceramic Grease
#7932
Bud oil is no good, use molybdenum grease or get some bicycle teflon chain grease.I use FinishLine Premium grease and have never had a bearing go on me.
Uniquexme havent had any hassle like that but cracks can happen from heat.
If the clutch is slipping and getting hot and then cools down the expansion and contraction can cause metal fatigue.
Wher you explained the cracks is in teh contact area of the clutch shoe and is the most likely reason for this.
Uniquexme havent had any hassle like that but cracks can happen from heat.
If the clutch is slipping and getting hot and then cools down the expansion and contraction can cause metal fatigue.
Wher you explained the cracks is in teh contact area of the clutch shoe and is the most likely reason for this.
#7933
the worst drive!!
today... it was die day to me...
My G4S go straight to cement wall in top speed.
i could not know the reason of no-control status.
i quess 2 facts of no-control.
1. battery badness
2. sanwa(airtronic) specktrum badness
i must stop my RC LIFE for some time..
My G4S go straight to cement wall in top speed.
i could not know the reason of no-control status.
i quess 2 facts of no-control.
1. battery badness
2. sanwa(airtronic) specktrum badness
i must stop my RC LIFE for some time..
#7934
Gansei, so sorry to see this and initially I wanted to say that its just part of the hobby but after seeing the extensive damage, I can understand with you why you want to stop RC for some time. Its going to cost a lot of money to fix everything.
Cheer up man ... come over to the UK and I'll lend you a real car to test - the 720! (That was supposed to cheer you up - not trying to say that the G4S/+ is a bad car )
Cheer up man ... come over to the UK and I'll lend you a real car to test - the 720! (That was supposed to cheer you up - not trying to say that the G4S/+ is a bad car )
#7935
OUCH !! thats not a good site
sorry !!! gansei
I can imagine how you feel.
Doubt that was the radio gear, must be battery, bad contact etc...
Just when you were getting somewhere with the setup.
If you were local ill loan you my spare car.
This is something that has happened to most us at some stage in our career.