V-ONE S Thread
#2806
Originally posted by ChrisO
I run both foam and rubber.
I race on small tracks... the size of 2 basket ball courts or 3-4net ball courts (depends on location)
I run both foam and rubber.
I race on small tracks... the size of 2 basket ball courts or 3-4net ball courts (depends on location)
gt
#2807
Tech Addict
This may be a stupid question, and it most probably is.... but can you use a digital servo with an AM Radio?
#2809
Tech Addict
Originally posted by Sp Racer
digital on am.....yep
digital on am.....yep
#2811
Originally posted by V-One S Racer
This may be a stupid question, and it most probably is.... but can you use a digital servo with an AM Radio?
This may be a stupid question, and it most probably is.... but can you use a digital servo with an AM Radio?
Yes you can, but it is only gonna be as fast as the transmitter and receiver unit that its being used with, so your probably not going to benefit much.
gt
#2812
radio box
Sorry Nitro dave, heres a better shot
gt
gt
#2813
can i see some pics of the modded engine squizzy or sp?
i wasnt gunna do anything drastic.. i wasnt planning on touching the port timing ... just planning on smoothing out the flow of gases till it gets to the port
and does anyones GS-15R have holes in the crank? like at the end where the crank pin is?
i read on SP's website that there is 2 different types of crankshafts you can get
i wasnt gunna do anything drastic.. i wasnt planning on touching the port timing ... just planning on smoothing out the flow of gases till it gets to the port
and does anyones GS-15R have holes in the crank? like at the end where the crank pin is?
i read on SP's website that there is 2 different types of crankshafts you can get
#2814
Originally posted by sausage_link
can i see some pics of the modded engine squizzy or sp?
i wasnt gunna do anything drastic.. i wasnt planning on touching the port timing ... just planning on smoothing out the flow of gases till it gets to the port
and does anyones GS-15R have holes in the crank? like at the end where the crank pin is?
i read on SP's website that there is 2 different types of crankshafts you can get
can i see some pics of the modded engine squizzy or sp?
i wasnt gunna do anything drastic.. i wasnt planning on touching the port timing ... just planning on smoothing out the flow of gases till it gets to the port
and does anyones GS-15R have holes in the crank? like at the end where the crank pin is?
i read on SP's website that there is 2 different types of crankshafts you can get
gt
#2815
Originally posted by Sp Racer
..........it doesn't matter what it seems!
..........it doesn't matter what it seems!
gt
#2816
hehe my bad :P
i was just going to shamfer the ports for improved air and fuel flow
i was just going to shamfer the ports for improved air and fuel flow
#2818
Tech Addict
I HATE KYOSHO
Fu(ken 18$ for 1 puny bearing, what a rip off.
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off
they use wierd ass sizes so u cant get the bearing from n e were.
cept from a bearing shop, specially made, and then they end up at 18$ a bearing in the shop
bloody hell its a rip off
so if u ever brake a couple of bearings, buy a new car.
Nitro dave: How much u want for the new pads?
Oh yeah, i now got the car running allright on the blocks, dont know how it will go on the track, hopefully better then last meet.
i oiled and cleaned all the bearings in the car from the main shaft back. god how a good clean in 2-stroke fuel makes the spin a lot better.
just need to tune my engine on the track now
it was too late to throw it out on the road to tune it.
Fu(ken 18$ for 1 puny bearing, what a rip off.
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off
they use wierd ass sizes so u cant get the bearing from n e were.
cept from a bearing shop, specially made, and then they end up at 18$ a bearing in the shop
bloody hell its a rip off
so if u ever brake a couple of bearings, buy a new car.
Nitro dave: How much u want for the new pads?
Oh yeah, i now got the car running allright on the blocks, dont know how it will go on the track, hopefully better then last meet.
i oiled and cleaned all the bearings in the car from the main shaft back. god how a good clean in 2-stroke fuel makes the spin a lot better.
just need to tune my engine on the track now
it was too late to throw it out on the road to tune it.
#2819
Originally posted by V-One S
I HATE KYOSHO
Fu(ken 18$ for 1 puny bearing, what a rip off.
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off
they use wierd ass sizes so u cant get the bearing from n e were.
cept from a bearing shop, specially made, and then they end up at 18$ a bearing in the shop
bloody hell its a rip off
so if u ever brake a couple of bearings, buy a new car.
Nitro dave: How much u want for the new pads?
Oh yeah, i now got the car running allright on the blocks, dont know how it will go on the track, hopefully better then last meet.
i oiled and cleaned all the bearings in the car from the main shaft back. god how a good clean in 2-stroke fuel makes the spin a lot better.
just need to tune my engine on the track now
it was too late to throw it out on the road to tune it.
I HATE KYOSHO
Fu(ken 18$ for 1 puny bearing, what a rip off.
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off
they use wierd ass sizes so u cant get the bearing from n e were.
cept from a bearing shop, specially made, and then they end up at 18$ a bearing in the shop
bloody hell its a rip off
so if u ever brake a couple of bearings, buy a new car.
Nitro dave: How much u want for the new pads?
Oh yeah, i now got the car running allright on the blocks, dont know how it will go on the track, hopefully better then last meet.
i oiled and cleaned all the bearings in the car from the main shaft back. god how a good clean in 2-stroke fuel makes the spin a lot better.
just need to tune my engine on the track now
it was too late to throw it out on the road to tune it.
How bizzare, I buy mine (including that size) from frontline hobbies for $2 each! In fact I keep around 6 of every size in my spares box!
gt
#2820
Tech Master
iTrader: (12)
18$ for 1 puny bearing, what a rip off.
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off
Thats wat dawn trading is selling the 12*18*4mm bearing at
wat a bloody rip off