Serpent 710
10-20-2004, 10:16 AM
Re: Re: Servo Saver
Originally posted by Julius
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
Should I set longer too? How much?
Thanks
10-20-2004, 10:20 AM
Re: Re: Servo Saver
Originally posted by Julius
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
Thanks
10-20-2004, 11:12 AM
Re: Re: Re: Servo Saver
Originally posted by jag
The end-points is fine but could you define "a little longer" for the link? If it matters, I am using a Hitec 5945 servo.
Thanks
The end-points is fine but could you define "a little longer" for the link? If it matters, I am using a Hitec 5945 servo.
Thanks
You want to get the saver in the center position with the servo arm leaning slightly forward.
If you get equal throw in both directions with close left/right end point settings on your transmitter you're ok.
10-20-2004, 11:33 AM
Re: Re: Re: Re: Servo Saver
Originally posted by Julius
I wouldn't know how much longer. But we changed the angle between the two parts of the servo saver. Before at maximum left throw the saver and the link to the servo would be almost in a straight line which was not ideal.
You want to get the saver in the center position with the servo arm leaning slightly forward.
If you get equal throw in both directions with close left/right end point settings on your transmitter you're ok.
I wouldn't know how much longer. But we changed the angle between the two parts of the servo saver. Before at maximum left throw the saver and the link to the servo would be almost in a straight line which was not ideal.
You want to get the saver in the center position with the servo arm leaning slightly forward.
If you get equal throw in both directions with close left/right end point settings on your transmitter you're ok.
It's great having you here for assistance.
Thanks alot.
Jim
10-20-2004, 11:46 AM
Where has The Border shop gone?
Just wanted to go to the Border shop and it's not there!!! 
Trying both www.the-border.com and www.the-border.nl land me at a Computer parts retailer (Dijkstra Online Shop)
Have they been hacked?
Mark.
Trying both www.the-border.com and www.the-border.nl land me at a Computer parts retailer (Dijkstra Online Shop)
Have they been hacked?
Mark.
10-20-2004, 11:51 AM
Tech Regular
Re: Where has The Border shop gone?
Originally posted by markp27
Just wanted to go to the Border shop and it's not there!!!
Trying both www.the-border.com and www.the-border.nl land me at a Computer parts retailer (Dijkstra Online Shop)
Have they been hacked?
Mark.
Just wanted to go to the Border shop and it's not there!!!
Trying both www.the-border.com and www.the-border.nl land me at a Computer parts retailer (Dijkstra Online Shop)
Have they been hacked?
Mark.
Try this:
http://shop.the-border.nl/customer/home.php
That way you fool the hackers
Thomas
10-20-2004, 12:19 PM
Re: Re: Where has The Border shop gone?
Originally posted by 840918001
Hi,
Try this:
http://shop.the-border.nl/customer/home.php
That way you fool the hackers
Thomas
Hi,
Try this:
http://shop.the-border.nl/customer/home.php
That way you fool the hackers
Thomas
10-20-2004, 02:05 PM
Re: Re: Re: Re: Re: Servo Saver
Originally posted by jag
So the angle of the mounts has changed a little bit. I will keep that in mind when I install it. Should the lever hit either of the front bulkheads? It looks very close right now. Need I be concerned about the clearance at the front pully?
It's great having you here for assistance.
Thanks alot.
Jim
So the angle of the mounts has changed a little bit. I will keep that in mind when I install it. Should the lever hit either of the front bulkheads? It looks very close right now. Need I be concerned about the clearance at the front pully?
It's great having you here for assistance.
Thanks alot.
Jim
10-20-2004, 06:52 PM
Originally posted by Sow&Steady
Because he can't have an Apple, he Thinks Different?
Because he can't have an Apple, he Thinks Different?
Those who think different are the ones that makes the difference.
10-20-2004, 06:52 PM
Re: Re: Servo Saver
Originally posted by Julius
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
You will need to make the steering link between the servo and servosaver a little longer, and reset your end-point settings on the transmitter.
10-20-2004, 06:57 PM
Re: Re: Re: Re: Re: Servo Saver
Originally posted by jag
Need I be concerned about the clearance at the front pully?
Need I be concerned about the clearance at the front pully?
If you're using the front ball diff, then you need to change to the new 2 piece diff clamp that comes packaged together with the new servo saver (802145) for better clearance. Or you can get that part separately (802387).
10-20-2004, 07:02 PM
Originally posted by rcpanama
I do have the 2.5mm install is 2.5mm inside the ball (stiffer)
I do have the 2.5mm install is 2.5mm inside the ball (stiffer)
Mounting it inside gives a softer setting.
Originally posted by rcpanama
I have the new MID position that will change from LT to mid position before LB, I might use this change to see.
I have the new MID position that will change from LT to mid position before LB, I might use this change to see.
I got that some time already but never thought of installing it.
10-20-2004, 09:40 PM
Originally posted by InitialD
Those who think different are the ones that makes the difference.
Those who think different are the ones that makes the difference.
10-20-2004, 10:12 PM
Originally posted by markp27
Thanks, D
Thanks, D
10-20-2004, 10:34 PM
Originally posted by InitialD
That does not include those with different operating systems !
That does not include those with different operating systems !
