MTX 5
#2806
#2807
Tech Fanatic
come on boys have we fixed them so good that no one has anything to say my grandson put his 5 on shelf after nats/aus till QLD next month cause he bid not want to were it out he has saved pop a $$$$ +he has a real car had to spend his own money on petrol nearly made him cry
greg
greg
Last edited by greg.dawn; 06-06-2013 at 01:54 AM.
#2808
The mtx5 is working really well now, so it's all about fine tuning the car to give me what I want. Great car!
#2809
Tech Fanatic
I see the USA is still with us you lot haven't stops shooting each other yet they whinge about the road toll but you lot love your guns puts the road toll to shame its raining again sunday glad to see your 5 is aright you can see I am board to death
#2811
pump all the air bubbles out before you close the diff up
#2813
Tech Adept
#2814
Tech Apprentice
JJ's latest MTX5 setup sheet from 2013 Byron Nitro Challenge
http://www.jjwangracing.com/setup-sheets-nitro/
http://www.jjwangracing.com/setup-sheets-nitro/
#2815
Tech Apprentice
JJ's latest MTX5 setup sheet from 2013 Byron Nitro Challenge
http://www.jjwangracing.com/setup-sheets-nitro/
http://www.jjwangracing.com/setup-sheets-nitro/
#2816
Tech Fanatic
iTrader: (25)
Well done Robert
Well it's great to see Robert doing well in the Euro Nitro Series.
Both in 1/8 & 1/10.
Great work mate.
I was keen to see what if any trick bits he's running and I like to see his setup data after this race.
I had a look at the photos of his MTX5 and saw a few neat tricks and see if you guys can spot them.
Front diff, original style chassis with some extra holes, maybe an new engine mount hole pattern, small receiver battery, springs? check out the rears.
I see he is still using his carbon cross brace but no rear brace as many are using.
Really good to see an MTX5 back in the top listing all the best for tommrow Robert.
Steve H
Both in 1/8 & 1/10.
Great work mate.
I was keen to see what if any trick bits he's running and I like to see his setup data after this race.
I had a look at the photos of his MTX5 and saw a few neat tricks and see if you guys can spot them.
Front diff, original style chassis with some extra holes, maybe an new engine mount hole pattern, small receiver battery, springs? check out the rears.
I see he is still using his carbon cross brace but no rear brace as many are using.
Really good to see an MTX5 back in the top listing all the best for tommrow Robert.
Steve H
Last edited by shanwright; 06-29-2013 at 08:51 PM. Reason: Spelling.
#2818
Tech Regular
iTrader: (4)
Did you notice Robert's brace along side the two speed shaft?
http://ens.redrc.net/wp-content/uplo...06/Sat_cf4.jpg
what kind of battery do you think he is running?
http://ens.redrc.net/wp-content/uplo...06/Sat_cf4.jpg
what kind of battery do you think he is running?
#2819
Tech Regular
iTrader: (4)
Well it's great to see Robert doing well in the Euro Nitro Series.
Both in 1/8 & 1/10.
Great work mate.
I was keen to see what if any trick bits he's running and I like to see his setup data after this race.
I had a look at the photos of his MTX5 and saw a few neat tricks and see if you guys can spot them.
Front diff, original style chassis with some extra holes, maybe an new engine mount hole pattern, small receiver battery, springs? check out the rears.
I see he is still using his carbon cross brace but no rear brace as many are using.
Really good to see an MTX5 back in the top listing all the best for tommrow Robert.
Steve H
Both in 1/8 & 1/10.
Great work mate.
I was keen to see what if any trick bits he's running and I like to see his setup data after this race.
I had a look at the photos of his MTX5 and saw a few neat tricks and see if you guys can spot them.
Front diff, original style chassis with some extra holes, maybe an new engine mount hole pattern, small receiver battery, springs? check out the rears.
I see he is still using his carbon cross brace but no rear brace as many are using.
Really good to see an MTX5 back in the top listing all the best for tommrow Robert.
Steve H
http://ens.redrc.net/wp-content/uplo...06/Sat_cf7.jpg
#2820
Did you notice Robert's brace along side the two speed shaft?
http://ens.redrc.net/wp-content/uplo...06/Sat_cf4.jpg
http://ens.redrc.net/wp-content/uplo...06/Sat_cf4.jpg