Kyosho VoneR Thread
#5416
Jedi the most important thing that Pattella forgot to mention.
ie a front oneway not the easiest thing to drive if you are a newby as you have to drive with a lot less brakes.
So as he said learn to drive the V1R and set it up.
then when your confident driving that car and can see what changes to setup does what to the car then upgrade.
Because just getting a newer car wont make you a better diver..
ie a front oneway not the easiest thing to drive if you are a newby as you have to drive with a lot less brakes.
So as he said learn to drive the V1R and set it up.
then when your confident driving that car and can see what changes to setup does what to the car then upgrade.
Because just getting a newer car wont make you a better diver..
#5417
Tech Rookie
front diff
I am need help I need to put a front diff from parts and need to get the part # please help
Where do you all get parts for the y-oner over seas or from tower
Where do you all get parts for the y-oner over seas or from tower
#5418
Re: To Patelladragger...
Originally posted by RClover
Do u have a pic of your car?
Do u have a pic of your car?
Na seriously I've had no problems with the kfactory tank or the stock tank.
#5419
New fuel tank seals can be purchased for the voner tank. The part No. is 92050-01. There is no real difference in the handling of the car between the two tanks.
#5420
So the culprit is...
Originally posted by rjl
New fuel tank seals can be purchased for the voner tank. The part No. is 92050-01. There is no real difference in the handling of the car between the two tanks.
New fuel tank seals can be purchased for the voner tank. The part No. is 92050-01. There is no real difference in the handling of the car between the two tanks.
#5421
Re: front diff
Originally posted by emt152
I am need help I need to put a front diff from parts and need to get the part # please help
Where do you all get parts for the y-oner over seas or from tower
I am need help I need to put a front diff from parts and need to get the part # please help
Where do you all get parts for the y-oner over seas or from tower
Item #
BS107 Bevel Shaft
VZ012 Diff Gear Set
VZ009 Diff Pulley Set
VZ015 Diff Joint
Diff Oil
You will need 2 of the VZ015 if you plan on building both front and rear diffs. I believe Tower has all of the items in stock.
#5422
Tech Master
Patella: Did you order those gears
#5423
Tech Master
Manticore: I got my package in the mail today
Boy that was faster than the last one you sent me
Boy that was faster than the last one you sent me
#5424
Originally posted by HEYALIGNMENTGUY
Manticore: I got my package in the mail today
Boy that was faster than the last one you sent me
Manticore: I got my package in the mail today
Boy that was faster than the last one you sent me
#5425
Originally posted by Manticore
Great!!
Great!!
Did you hear the story about Kyosho getting the 3 ports and 5 ports mixed up in the boxes???
#5426
Originally posted by dtm
Manticore- your favourite friend from PG says the Rossi engine SUX......Siro Rulez!!!!
Did you hear the story about Kyosho getting the 3 ports and 5 ports mixed up in the boxes???
Manticore- your favourite friend from PG says the Rossi engine SUX......Siro Rulez!!!!
Did you hear the story about Kyosho getting the 3 ports and 5 ports mixed up in the boxes???
I know that. It is simple to find it out looking from the exhaust port. There should have 2 small ports at each corners of the exhaust.
#5427
Originally posted by Manticore
who are you talking about??
who are you talking about??
#5428
Originally posted by dtm
Your favourite guy who likes to replace his conrods after 1 gallon of fuel!!
Your favourite guy who likes to replace his conrods after 1 gallon of fuel!!
#5429
Tech Elite
RCLover
Use a #4 or 3mm split lock washer to keep the caphead screw from backing out on the 2 speed. I would use one on the Centax also if you have one.
No mess from threadlock and you can take the screw out when you want.
Use a #4 or 3mm split lock washer to keep the caphead screw from backing out on the 2 speed. I would use one on the Centax also if you have one.
No mess from threadlock and you can take the screw out when you want.
#5430
Tech Rookie
What hop up parts are recomended to lighten up the V1rr? Ive been looking into Kawahara parts but I am not exactly sure what would actually make the car lighter. Ive also seen that Kyosho makes some titanium parts. Which ones would be helpful? I was thinking turnbuckles and titanium screws, but I'm not sure if Kyosho makes a screw set specifically for the RR. Any advice would be great. Thanks