Kyosho V-ONE RRR Evo
#556
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
this ordered came a bit later still waiting for a few more kawahara parts to arrive so that my project is complete
kawahara roll bar set
kawahara roll bar set
#557
Originally Posted by esham
Guys need help here. I do have problem with my V1RRR Evo, understeer on, off power. Seem too much grip at rear. My current setting is:-
Front/Rear
Dif - Oneway/ 10K - sometime 30K
Shock oil- 40/40
Shock Position - mid/mid
Spring- RRR Evo blue spring front/rear
Swaybar- 0°/45°
Tires - 38/43 - Did used 40 at rear it make more understeer
Downstop - 0/4mm
Tires Dia - 62/64
Trackwidth- 199/200
Ride Height- 6.5-7.5
Camber- 1.5/3
Toe- 1/-2.5
Body- Mazda 6
Track Traction - mid
Anything wrong here? I start thinking to change back to laydown servo where i got hang on it. Welcome and Thanks for your opinion
Front/Rear
Dif - Oneway/ 10K - sometime 30K
Shock oil- 40/40
Shock Position - mid/mid
Spring- RRR Evo blue spring front/rear
Swaybar- 0°/45°
Tires - 38/43 - Did used 40 at rear it make more understeer
Downstop - 0/4mm
Tires Dia - 62/64
Trackwidth- 199/200
Ride Height- 6.5-7.5
Camber- 1.5/3
Toe- 1/-2.5
Body- Mazda 6
Track Traction - mid
Anything wrong here? I start thinking to change back to laydown servo where i got hang on it. Welcome and Thanks for your opinion
Also
-softer Tires in the front
-softer springs in front
-harder spring in rear
-more front droop (ie. -1)
try the tuning first before you switch the bodies.
#559
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
Originally Posted by fritzD
doki,
those are some sexy upgrades.. hehehe
those are some sexy upgrades.. hehehe
#560
Originally Posted by Amon
forgot where i downloaded these images from...they were named toso.jpeg and shimo.jpeg respectively...car posted earlier looks like toso's...but i could be wrong...
Does anyone know where I can get that rear sway bar (blade) that is in the images in the previous page....?????
#561
Originally Posted by ickvanovs
i like the new upper deck layout
#562
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
Originally Posted by Heartsword
There is the new design for locking the fifth body shell post on the deck from KM Racing.
#563
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
finally found time to install the kfactory special rear brace very nice fit it adds rigidity to the rear with a very nice silver finish
#564
Tech Elite
iTrader: (2)
Join Date: Dec 2003
Location: Cebu City, Philippines and Ocala, Florida, USA
Posts: 3,840
Trader Rating: 2 (100%+)
v1rrr evo
i also installed the kawahara roll bar set this gives more protection for the engine head since it is much higher compared to the stock roll bar
#566
Tech Master
iTrader: (3)
Join Date: Dec 2001
Location: Costa Del Sol, Marbella, Spain www.bradir.net
Posts: 1,456
Trader Rating: 3 (100%+)
hey
doki: seems like the rollbar mounts are exactly the same on our old RR rollbar mounts, i still have them, think it will fit?
#567
Tech Addict
Originally Posted by mrgsr
do the v-one rrr springs fit the rrr evo shocks ?
#569
Tech Rookie
sirio evo3 sti
I have a question on this sirio engine.
There is always a bit play when I try to move the crankshaft away from the engine. No matter how tight the nut on the flywheel.
the play is around 0.5 mm. Is this normal ? I try different cone under the flywheel but have no luck. I also put some spacer before putting the cone, still I have the play. this not happening with my novarossi S5 engine earlier.
one more question regarding the spur gears. any tip of preventing the strip spur gears ? I try to set correct gear mesh by putting a piece of paper between but it still happening once in a while. I am thinking of making the chassis a bit rough under the bolt/nut. any idea ?
I love this kyosho car alot, I just converted it to rrr-evo. I did not notice the different in handling so far, but I do like the layout of radio plate better.
thanks
There is always a bit play when I try to move the crankshaft away from the engine. No matter how tight the nut on the flywheel.
the play is around 0.5 mm. Is this normal ? I try different cone under the flywheel but have no luck. I also put some spacer before putting the cone, still I have the play. this not happening with my novarossi S5 engine earlier.
one more question regarding the spur gears. any tip of preventing the strip spur gears ? I try to set correct gear mesh by putting a piece of paper between but it still happening once in a while. I am thinking of making the chassis a bit rough under the bolt/nut. any idea ?
I love this kyosho car alot, I just converted it to rrr-evo. I did not notice the different in handling so far, but I do like the layout of radio plate better.
thanks