R/C Tech Forums - View Profile: ArronRC
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

ArronRC's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

ArronRC ArronRC is offline

Tech Adept

Last Activity: 08-23-2019 11:34 AM

About Me

  • About ArronRC
    Biography
    Works at AMR ENGINES on Facebook. www.AMR Engines.com
    Location
    Jeffersonville, IN

Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: 08-23-2019 11:34 AM
  • Join Date: 06-21-2009
  • Referrals: 0

Friends

Showing Friends 1 to 3 of 3

Visitor Messages

Showing Visitor Messages 1 to 3 of 3
  1. 11-02-2015 12:55 PM - permalink
    Thanks, lots of good stuff to look at. I "liked" the page.
  2. TimMo846
    03-19-2014 04:36 PM - permalink
    YES SIR!!!!!!!!!!!!!!!! It rips!!!!!!!!!
  3. 03-19-2014 01:05 PM - permalink
    check out section 8 racing on face book! there profile picture is a sleeve out of a OS speed engine. they do great engine work.

Likes Given

28 Likes
  1. ArronRC liked post by Andyg01 On thread : Venturi Testers Needed
    We plan to do a back to back test this Sunday, fitted to a B2102 BUT it now has a B2101 crank fitted along with a 21J carb with the tessman insert, 5.8mm. I suppose this is a TY2 motor now:lol:, but...
    Liked On: 10-04-2017, 10:01 PM
    Posted On: 10-04-2017, 08:06 AM
  2. ArronRC liked post by Motorman007 On thread : O.S. SPEED .21 XZB SPEC. II
    Bess are ceramic bearings needed? I noticed that the Tekno OS does not come with ceramic bearings. Which makes it a couple dollars cheaper versus the OS label motor.. you and I remember the ceramic...
    Liked On: 09-15-2017, 08:49 PM
    Posted On: 09-12-2017, 05:31 AM
  3. ArronRC liked post by Roelof On thread : Maximising engine characteristics.
    The advance of an aircraft engine is the cooling from the prop. A high and reasonable steady cooling makes the engine less critical. And fyi, our engine was in the base an aircraft engine. But the...
    Liked On: 09-07-2017, 10:59 PM
    Posted On: 09-07-2017, 05:20 AM
  4. ArronRC liked post by 22Racer On thread : Engine has no compression
    As said earlier, if it lost compression all of a sudden something happened. Most likely is dirt getting in. In that case the rod and crank should be checked also as dirt can wear those also. It is a...
    Liked On: 08-27-2017, 02:45 PM
    Posted On: 08-27-2017, 10:59 AM
  5. ArronRC liked post by stanleyw808 On thread : The Nitroshop
    Hello Neal, I would like to ask about Your service for DLC Coating a Crankshaft. Do you Grind the Bearing Seats and the Crankshaft Pin before the coating? Cheers.. :)
    Liked On: 07-02-2017, 11:24 PM
    Posted On: 07-02-2017, 10:04 PM
  6. ArronRC liked post by Roelof On thread : Heat cycle engine break in process?
    There are 1001 methodes to run in an engine, all will do basically the same. Heatcycle has a reason, it has to do with shifting molecules when cooling down but finally that will stabalize in any...
    Liked On: 06-26-2017, 12:12 AM
    Posted On: 06-25-2017, 01:10 PM
  7. ArronRC liked post by savagesam On thread : The Official BLOK Engines Thread
    Well I thought I should share this video, I had a BLOK .21am broken in using the EBIS - Easy break in system, the engine had a 4hr break in done, I cleaned all the oil from the engine and rebuilt it,...
    Liked On: 06-24-2017, 09:42 PM
    Posted On: 06-24-2017, 04:33 AM
  8. ArronRC liked post by MX304 On thread : Team Associated RC8B3 Nitro Team Kit
    A lot of people had issues making the original V1s work, even though the team drivers preferred them. When the truggy came out it had the V2 diffs, and a lot of people switched to them in the buggy....
    Liked On: 05-05-2017, 07:09 AM
    Posted On: 05-05-2017, 06:43 AM
  9. ArronRC liked post by blackbeardrollo On thread : Os long stroke crank with big bore sleeve
    Yep same length, and it fired right up and idled nicely, I'll try it tomorrow and post an update
    Liked On: 04-23-2017, 06:42 AM
    Posted On: 04-23-2017, 12:31 AM
  10. ArronRC liked post by EBMods On thread : Kinetic R/C™ GR8-21™
    https://www.kineticrc.com/assets/images/partspic2.jpg https://www.kineticrc.com/assets/images/gr8-21pic3.jpg https://www.kineticrc.com/assets/images/gr8-21pic8.jpg
    Liked On: 04-20-2017, 03:01 PM
    Posted On: 04-19-2017, 04:27 AM
  11. ArronRC liked post by ROSCOE On thread : Triton RC new engine...
    Wrong thread guys! Handle your personal problems somewhere else. Post em if you got em! Lol ...
    Liked On: 04-09-2017, 07:34 PM
    Posted On: 04-09-2017, 06:42 AM
  12. ArronRC liked post by EBMods On thread : Venturi Testers Needed
    No, sorry you can not. It will affect the way it's designed to work. My 7mm flows 8.2cfm, same as the OS and Novarossi 8mm. I studied and tested different inside surface finishes on the flow...
    Liked On: 03-12-2017, 09:32 AM
    Posted On: 02-27-2017, 05:17 AM
  13. ArronRC liked post by EBMods On thread : Venturi Testers Needed
    Just wanted to let everyone know that I now have the Venturi listed on EBay if anyone is interested. EBMods 7mm Venturi, Fits OS and Novarossi Engines | eBay...
    Liked On: 03-11-2017, 09:40 PM
    Posted On: 03-11-2017, 12:15 PM
Page 2 of 2
1
2

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.