R/C Tech Forums - Tamiya TRF419

Here: https://www.facebook.com/tamiyaracing.dk?fref=photo

Today I will done my new Protoform LW Dodge Dart. Tonight I run on carpet again with my BD7 Setup :nod:

Works now. He's running 0.5 under each block! This will increase the camber gain which is causing your grip issue (too planted). I would remove the 0.5 both front and rear. The front link heights look decent. The rear outer link shims should be dropped down to 1 mm, 4 mm is a little excessive. :weird:

Front camber - 1.5
Rear camber is good

Toe out .5 or 1

CW22	01-21-2015 07:38 AM

Quote:

Originally Posted by cplus (Post 13796167)

move the sticker then :D

its just a sticker right? R1rurks don't make an ECU yet do they?

No, that's the authentic R1 esc.
Not in the market yet.

RedBullFiXX

01-21-2015 07:47 AM

Quote:

Originally Posted by EDWARD2003 (Post 13796365)

Works now. He's running 0.5 under each block! This will increase the camber gain<--I don't believe that is correct )which is causing your grip issue (too planted). I would remove the 0.5 both front and rear. The front link heights look decent. The rear outer link shims should be dropped down to 1 mm, 4 mm is a little excessive. :weird:

Front camber - 1.5
Rear camber is good

Toe out .5 or 1

BIBOY

01-21-2015 08:16 AM

Quote:

Originally Posted by cplus (Post 13796167)

move the sticker then :D

its just a sticker right? R1rurks don't make an ECU yet do they?

that is an R1 esc soon to be at you local hobby shop :nod:

BIBOY

01-21-2015 08:25 AM

Quote:

Originally Posted by cplus (Post 13795975)

Any reason for the ESC orientation. Looks more awkward than it could be if you rotated it 90deg clockwise?

i did not want to twist the wires the esc has similar config as the Orca the motor wire output is reversed .... i really wanted to show the R1 logo on the side :ha:

maxepower

01-21-2015 11:59 AM

Quote:

Originally Posted by BIBOY (Post 13796728)

i did not want to twist the wires the esc has similar config as the Orca the motor wire output is reversed .... i really wanted to show the R1 logo on the side :ha:

:nod:

EDWARD2003

01-21-2015 03:26 PM

Quote:

Originally Posted by RedBullFiXX (Post 13796659)

Oops, I forgot to write 0.5 mm also raises the roll centre. Normally you use the camber link to adjust camber gain. Shimming the blocks has more effect on roll centre than camber gain.

Raman

01-21-2015 10:10 PM

Mine arrived today and I started the build this evening. All smiles so far.. Always a pleasure building a Tamiya, specially a TRF.

Just out of curiosity, does anyone know, what's the weight of the clear silicone fluid, that the manual recommends for the differential?

RC Passion

01-21-2015 10:31 PM

Quote:

Originally Posted by Raman (Post 13798285)

Man! I wish I could drop coin on a 419! You're not giving up on the TB04 are you?

ittjv

01-21-2015 10:40 PM

Quote:

Originally Posted by Raman (Post 13798285)

Tamiya usually includes 900wt for the diff.

Simmi

01-21-2015 10:50 PM

2 Attachment(s)

Here are some Pics about the HOT RACE in Italy:

https://www.facebook.com/Hotracetyre.../photos_stream

And here also my final Setup for Carpet ;)

C van der Hagen

01-22-2015 02:38 AM

Quote:

Originally Posted by Raman (Post 13798285)

#900

blf	01-22-2015 10:14 AM

Are there "better", metal diff gears that would be advisable to replace the GV/51567 tree?

Why does my EVO 6 have metal gears and a plastic/static cross pin and the exact opposite on the 419....plastic gears with alum/keyed (x2) cross pins?

Marcika

01-22-2015 11:49 AM

hey,

Does anybody know rc arena in Warsaw, Poland? Or where there is possibility to practice either on carpet or asphalt.

Thanks,
Marton

All times are GMT -7. It is currently 08:45 AM.

Page 55 of 309

Show 40 post(s) from this thread on one page