New Novak Brusless System
#2056
so, with much nervousness, i ran my 3.5R in my 415MSXX this weekend...all i can say is whhhhhhhoooooooossssssshhhhhhhh!!! that thing is like a rocket!!!
it thunders down our main straight and the braking is crisp and accurate! power on the infield is phenomenal as the car darts from one turn to the next.
i am very very happy with my GTB and 3.5R Veocity motor.
it thunders down our main straight and the braking is crisp and accurate! power on the infield is phenomenal as the car darts from one turn to the next.
i am very very happy with my GTB and 3.5R Veocity motor.
#2057
Tech Regular
I am thinking of getting either a 3.5R or 4.5R for my 415MSX...which one would be a better choice?
#2059
in my limited experience with brushless, i would say get the 3.5, it is the best motor Novak has to offer. i am completely stoked with mine. besides, sooner or later you will want more....and the 3.5R gives it all!!!
#2060
Tech Addict
iTrader: (10)
Originally Posted by RocketRacer
in my limited experience with brushless, i would say get the 3.5, it is the best motor Novak has to offer. i am completely stoked with mine. besides, sooner or later you will want more....and the 3.5R gives it all!!!
#2062
Some of our team guys don't even run the 3.5 for all conditions. They run the 4.5 as it's easier to drive, and a bit "tamer" if you will.
Alum, Start out about 2-3 teeth taller then the regular stock motors. Go for around 130-140F as a final Temp of the motor and you should be pretty pleased. Gearing is a tough call for sure, it's different for a lot of guys.
Alum, Start out about 2-3 teeth taller then the regular stock motors. Go for around 130-140F as a final Temp of the motor and you should be pretty pleased. Gearing is a tough call for sure, it's different for a lot of guys.
#2065
Tech Regular
iTrader: (4)
anyone know if this is the correct bearing for the older style endbell (the 4300 and 5200)
http://cgi.ebay.com.au/1-8x3-8-x5-32...QQcmdZViewItem
INNER DIAMETER: 1/8"
OUTER DIAMETER: 3/8"
HEIGHT: 5/32"
http://cgi.ebay.com.au/1-8x3-8-x5-32...QQcmdZViewItem
INNER DIAMETER: 1/8"
OUTER DIAMETER: 3/8"
HEIGHT: 5/32"
#2066
is it possible to use the slim type cap instead of e novak cap?
anyone tried?
anyone tried?
#2067
Tech Regular
I tried the smaller diameter cap that the new LRP's use and it was ok but the speedo ran cooler with the novak cap.
#2069
Tech Adept
i just installed my lipo batt together with the Novak Smart Stop for 2 cell , it happnes that when radio is off the car goes full power
shoudnt be a problem when normal operation but in case of radio signal loss its very dangerous
my setup is novak gtb , 5.5 BL , futaba R133F receiver, maxamps lipo 8000 and Novak 2 cell Smart Stop
help apreciated
thanks in advance
shoudnt be a problem when normal operation but in case of radio signal loss its very dangerous
my setup is novak gtb , 5.5 BL , futaba R133F receiver, maxamps lipo 8000 and Novak 2 cell Smart Stop
help apreciated
thanks in advance
#2070
Tech Adept
im so stupid , didnt read the manual ... there is a set up button ...
once i did the set up, all is right
once i did the set up, all is right