Hot Bodies Cyclone
Tech Champion
iTrader: (30)
The same problem with all aluminum parts - in a bad crash they will bend, sometimes so slightly you can't see it until you full disassmeble the car...
Plus aluminum is heavier than even the thickest plastic parts
Aluminum belong on some places, but not all over the car...Sometimes they hurt the car more than they help with looks or performance
Plus aluminum is heavier than even the thickest plastic parts
Aluminum belong on some places, but not all over the car...Sometimes they hurt the car more than they help with looks or performance
Tech Regular
iTrader: (15)
Well if that is how I can add weight the that might be an option, I run a 4800 lipo and am about 150 grams under weight
Tech Fanatic
iTrader: (1)
I put HB aluminum knuckles on and have not broken a graphite C hub sense. The aluminum C hub will bend like previously stated so stay with graphite. The titanium ball studs are a must have. I race in 10.5 and mod with 4600 and 7700 motors and my crashes are spectacular
Last edited by Lazer Guy; 02-16-2008 at 08:48 AM.
Tech Elite
iTrader: (50)
Edit
Anyone know where I can get Edit RC products.
Cyclone titanium hinge pins, diff screws and ball studs?
Cyclone titanium hinge pins, diff screws and ball studs?
I put HB aluminum knuckles on and have not broken a graphite C hub sense. The aluminum C hub will bend like previously stated so stay with graphite. The titanium ball studs are a must have. I race in 10.5 and mod with 4600 and 7700 motors and my crashes are spectacular
Thanks,
Tech Fanatic
iTrader: (1)
I have seen them in a lot of places, sometimes under the HPI pro4 parts. That is what mine are. I should have said HPI not HB, but they are the same. Sorry about that I will look around and give you some places to get them.
RC MARKET has them, purple only HPI#31414... I will look for some more places.
RC MARKET has them, purple only HPI#31414... I will look for some more places.
Last edited by Lazer Guy; 02-16-2008 at 12:20 PM.
Tech Master
iTrader: (23)
Not like we'd wanna do it or anything but....Xray T2 C-hubs and knuckles will work on the Cyclone (the T2 is mostly a rip off of the Cyclone design anyhow, right).
However, the steering geometry will not be the same. Not sure how it would affect hanling and/or what could be done to compensate for the differences.
Just thought I'd mention it, Xray composite parts are pretty beefy.
Don't shoot the messenger!
However, the steering geometry will not be the same. Not sure how it would affect hanling and/or what could be done to compensate for the differences.
Just thought I'd mention it, Xray composite parts are pretty beefy.
Don't shoot the messenger!
Super Moderator
iTrader: (239)
Not like we'd wanna do it or anything but....Xray T2 C-hubs and knuckles will work on the Cyclone (the T2 is mostly a rip off of the Cyclone design anyhow, right).
However, the steering geometry will not be the same. Not sure how it would affect hanling and/or what could be done to compensate for the differences.
Just thought I'd mention it, Xray composite parts are pretty beefy.
Don't shoot the messenger!
However, the steering geometry will not be the same. Not sure how it would affect hanling and/or what could be done to compensate for the differences.
Just thought I'd mention it, Xray composite parts are pretty beefy.
Don't shoot the messenger!
Thanks,
Tech Master
iTrader: (23)
I gotta be honest, I do also own a 008.
Since we're taking about broken parts, at last nights club race I sheared off (that's right sheared off) a TIR stub axle right at the hex pin. I thought the TIR stuff was high end.....didn't even crack the C-hub, go figure.
Since we're taking about broken parts, at last nights club race I sheared off (that's right sheared off) a TIR stub axle right at the hex pin. I thought the TIR stuff was high end.....didn't even crack the C-hub, go figure.
Tech Fanatic
iTrader: (1)
I don't think the xray ones will go right on, HPI# 31414 will.
Tech Elite
iTrader: (28)
what should i gear a hara cyclone (assuming still stock) with a 10.5 motor?
mayeb even just give a good FDR (medium sized asphalt track)
mayeb even just give a good FDR (medium sized asphalt track)
xray just did what hot bodies could not. make a durable car. don't hate them because they made the cyclone inferior.
Super Moderator
iTrader: (239)
lol thats why i had some x ray team drivers came up to me last year at our reional race to borrow some of my Cyclone front and rear arms because it made their car handle better
Tech Fanatic
iTrader: (1)
LOL xraysteve you and them other 4 ugly cars are going down tomorrow. You know it and you believe it, Cyclone rules the rug. I've seen you brake lots of hight $ ugly parts.
I you put xray parts on your Cyclone it will be slower. Use only HB or HPI parts. except no substitute. lol
I you put xray parts on your Cyclone it will be slower. Use only HB or HPI parts. except no substitute. lol
Last edited by Lazer Guy; 02-16-2008 at 05:38 PM.