Hot Bodies Cyclone
#9377
Tech Master
#9378
#9381
Tech Champion
iTrader: (9)
http://www.blogs.se/media/photo/cimg...lbum_ID=237825
big pullies, and look how loose the belts are.
When can we get hold of these fella's?
big pullies, and look how loose the belts are.
When can we get hold of these fella's?
#9382
Tech Champion
iTrader: (9)
http://www.blogs.se/media/photo/cimg...lbum_ID=237825
big pullies, and look how loose the belts are.
When can we get hold of these fella's?
big pullies, and look how loose the belts are.
When can we get hold of these fella's?
#9384
Tech Champion
iTrader: (9)
That's what I thought too... and was thinking it might be 19T to get a 2.052 transmission ratio.
For those that PM'd me...
2.0 transmission: 36/18
the belts are very very loose at the moment... looking for front/rear belts that are 1 tooth less than stock.
for now this is what I'm using:
(2) sets of 3Racing red belt tension cams
(2) sets of 3Racing 18T pulleys
(1) rear belt tensioner
(2) Pro3 36T diff pulleys... one of them you'll need to ream out to fit the one-way or spool.
able to get to a 4.6fdr using a 106/46 5cell for 10.5bl.
2.1666 transmission: 39/18
(1) Yok BD rear belt 189mm 63T
(1) Mi3 front belt 510mm 171T
(2) sets of 3Racing red belt tension cams
(2) sets of 3Racing 18T pulleys
the yok rear belt is a perfect fit.. waiting on the Mi3 belt to arrive. and I'll confirm fit. with the stock front belt..it's way way too Tight!! don't try it!
if you do order the 18T 3racing pulleys..make sure you also order some replacement pulleys... they are made for the TAO5..but fit the cyclone mounts and come 2ea.. 16/17/18T
pics of the 18T pulley installed and 3Racing 5cell chassis.
For those that PM'd me...
2.0 transmission: 36/18
the belts are very very loose at the moment... looking for front/rear belts that are 1 tooth less than stock.
for now this is what I'm using:
(2) sets of 3Racing red belt tension cams
(2) sets of 3Racing 18T pulleys
(1) rear belt tensioner
(2) Pro3 36T diff pulleys... one of them you'll need to ream out to fit the one-way or spool.
able to get to a 4.6fdr using a 106/46 5cell for 10.5bl.
2.1666 transmission: 39/18
(1) Yok BD rear belt 189mm 63T
(1) Mi3 front belt 510mm 171T
(2) sets of 3Racing red belt tension cams
(2) sets of 3Racing 18T pulleys
the yok rear belt is a perfect fit.. waiting on the Mi3 belt to arrive. and I'll confirm fit. with the stock front belt..it's way way too Tight!! don't try it!
if you do order the 18T 3racing pulleys..make sure you also order some replacement pulleys... they are made for the TAO5..but fit the cyclone mounts and come 2ea.. 16/17/18T
pics of the 18T pulley installed and 3Racing 5cell chassis.
Last edited by rc-zombies; 08-07-2007 at 01:27 PM.
#9385
#9386
shocks
hi guys i am calling it shock ceepage when you see the top of your shock cap the black part wet even though you tighten it very tight always see little dampness any ideas.
#9388
have any of you purchased the middle heat sink from jet racing? i bought one but it has round indentions where the spur gear mounts
giving the bearings room to move up and down about 1/16" whereas the carbon one keeps the bearings snug. should i run this or keep the carbon and toss the jet one as a poorly designed aftermarket item?
giving the bearings room to move up and down about 1/16" whereas the carbon one keeps the bearings snug. should i run this or keep the carbon and toss the jet one as a poorly designed aftermarket item?
#9389
Tech Rookie
LIPO in the Cyclone
Hi,
I am a newbie here... can you guys help me?
Does anyone had fitted a trackpower lipo battery pack on the andy moore cyclone? what is the best way to do it?
With the stock pulley's diff and center, what is the best pinion/spur combination to use with a BL motor?
To calculate the final ratio with the stock pulley's what should i use? (spur/pinion)*2.4375?
Best regards,
Rodrigo
I am a newbie here... can you guys help me?
Does anyone had fitted a trackpower lipo battery pack on the andy moore cyclone? what is the best way to do it?
With the stock pulley's diff and center, what is the best pinion/spur combination to use with a BL motor?
To calculate the final ratio with the stock pulley's what should i use? (spur/pinion)*2.4375?
Best regards,
Rodrigo
#9390
Hi,
I am a newbie here... can you guys help me?
Does anyone had fitted a trackpower lipo battery pack on the andy moore cyclone? what is the best way to do it?
With the stock pulley's diff and center, what is the best pinion/spur combination to use with a BL motor?
To calculate the final ratio with the stock pulley's what should i use? (spur/pinion)*2.4375?
Best regards,
Rodrigo
I am a newbie here... can you guys help me?
Does anyone had fitted a trackpower lipo battery pack on the andy moore cyclone? what is the best way to do it?
With the stock pulley's diff and center, what is the best pinion/spur combination to use with a BL motor?
To calculate the final ratio with the stock pulley's what should i use? (spur/pinion)*2.4375?
Best regards,
Rodrigo
Theres the HB Cyclone is the cars selection, choose your spur, and your pinion till you find the fdr that you need
What BL motor is it?
And I dont know if those gold packs fit or not, cant help you there.