Hot Bodies Cyclone
#4487
Originally Posted by protc3
i am going to be trying that vs. through slots.i may do this to change the roll characterics of the car.pocketed slots raise the cell hence more leverage for chassis roll on the lighter side.it may be a better balance.i will let you know how it goes.
Jason - When can we expect to see the carpet chassis set for the cyclone? Jax has a new carpet track and I need a carpet chassis....pllllllllease hurry..
#4488
Tech Lord
iTrader: (13)
i will be up at jax in about 2 weeks to test it.i am making the new hinge pin blocks to increase the track width and then she is ready.once i get it proven,i will start running them off immediately.i am very optimistic about this kit.i can tell you this,this car in stock form is definately an asphalt car and a damn good one at that.but it needed to undergo alot of changes to perform on carpet as well as other proven carpet cars.i think i have it nailed.
#4489
Super Moderator
iTrader: (239)
Originally Posted by protc3
i will be up at jax in about 2 weeks to test it.i am making the new hinge pin blocks to increase the track width and then she is ready.once i get it proven,i will start running them off immediately.i am very optimistic about this kit.i can tell you this,this car in stock form is definately an asphalt car and a damn good one at that.but it needed to undergo alot of changes to perform on carpet as well as other proven carpet cars.i think i have it nailed.
#4490
Jason - Sounds sweet! Did Hara run a heavily modified car in Vegas? I wasn't at the race and can't tell by the pics.
#4493
true dat!
#4494
I beleive that Hara ran a chassis with no cut outs....I was pitted at the table behind him and managed to talk to him a little. Looked like it was pretty standard stuff except for the chassis and top deck.
#4495
Does anyone know where I can buy a V8 Capacitor and MM 55 amp diode as seen on Hara's car.
It looks a lot tidier than the barel cap on the Twister 2.1
It looks a lot tidier than the barel cap on the Twister 2.1
#4497
^^^ Thanks Man
#4498
Tech Master
Hello Racers!
I am currently building my Hara Cyclone! Can any one tell me what the extra grease is for? Not the White or Red cap. No this grease is clear and comes in a tube. It also has a part number, Z162. I have scoured the manual a few times and can’t find where it is meant to be used.
Also have any greased the one ways? I know they come with some oil/grease in them, but what have you all done?
Thanks for the help,
Snowy.
I am currently building my Hara Cyclone! Can any one tell me what the extra grease is for? Not the White or Red cap. No this grease is clear and comes in a tube. It also has a part number, Z162. I have scoured the manual a few times and can’t find where it is meant to be used.
Also have any greased the one ways? I know they come with some oil/grease in them, but what have you all done?
Thanks for the help,
Snowy.
#4500
Tech Master
iTrader: (37)
Originally Posted by Essnowyt
Hello Racers!
I am currently building my Hara Cyclone! Can any one tell me what the extra grease is for? Not the White or Red cap. No this grease is clear and comes in a tube. It also has a part number, Z162. I have scoured the manual a few times and can’t find where it is meant to be used.
Also have any greased the one ways? I know they come with some oil/grease in them, but what have you all done?
Thanks for the help,
Snowy.
I am currently building my Hara Cyclone! Can any one tell me what the extra grease is for? Not the White or Red cap. No this grease is clear and comes in a tube. It also has a part number, Z162. I have scoured the manual a few times and can’t find where it is meant to be used.
Also have any greased the one ways? I know they come with some oil/grease in them, but what have you all done?
Thanks for the help,
Snowy.