Ask Steve "The Evicerator" Weiss
#6752
The Evicerator
We generally recommend to keep temperatures on ESCs and motors under 160 degrees for the longest possible product life.
#6753
Tech Apprentice
Hi Steve, think you missed my q, why don't Novak's have current limiters any more? I thought this used to be a good way to control punch?
#6754
Tech Adept
iTrader: (3)
Steve, I have question about gearing? I usually run on tracks that are set up in parking lots which are usually 100' x 60'. This months state race(FSEARA) is at Kraceway in Kissimmee which looks very big in the pictures. Any way the question is what would be a good starting point for gearing in a Xray T2 007 with a Novak 17.5? Any advice would be great. Thank you.
Steve P.
p.s. the white line in the picture is the possible lay out.
Steve P.
p.s. the white line in the picture is the possible lay out.
#6756
The Evicerator
Hey Guys!
Sorry about the delay in answering questions...just been a very crazy last week or two!!
We went away from current limiters with brushed motors ... while there were times people liked the way it worked, when they wanted it off, they still thought it was limiting the current somehow... so we just started going away from using them...
Now that brushless is such a different animal, we may start playing around with them again!
Hi Steve,
Seems to me like most guys are running the 17.5's in the 3.5-3.75 range... this will of course varry with motor and ESC combination... if you are using a speed control that has alot of timing advance like the new LRP you may need to gear closer to 4.0.
Hope this helps!
Swimbikerun,
You're right, the 4 cell GTBs have been discontinued... don't know the exact reason why, but someone around here must have had a reason for it!
We still offer the combos through our shopatron site though...
http://www.shopatron.com/index/135.0.151.44788.0.0.0
Sorry about the delay in answering questions...just been a very crazy last week or two!!
Now that brushless is such a different animal, we may start playing around with them again!
Steve, I have question about gearing? I usually run on tracks that are set up in parking lots which are usually 100' x 60'. This months state race(FSEARA) is at Kraceway in Kissimmee which looks very big in the pictures. Any way the question is what would be a good starting point for gearing in a Xray T2 007 with a Novak 17.5? Any advice would be great. Thank you.
Steve P.
p.s. the white line in the picture is the possible lay out.
Steve P.
p.s. the white line in the picture is the possible lay out.
Seems to me like most guys are running the 17.5's in the 3.5-3.75 range... this will of course varry with motor and ESC combination... if you are using a speed control that has alot of timing advance like the new LRP you may need to gear closer to 4.0.
Hope this helps!
Swimbikerun,
You're right, the 4 cell GTBs have been discontinued... don't know the exact reason why, but someone around here must have had a reason for it!
We still offer the combos through our shopatron site though...
http://www.shopatron.com/index/135.0.151.44788.0.0.0
#6758
The Evicerator
Hey Chris,
I'm really not sure why they eliminated the XBR from all the spec charts... probably because the specs are pretty much idential to the Havoc...
Maybe they felt like it would be confusing having both ESC's listed...?
I'm really not sure why they eliminated the XBR from all the spec charts... probably because the specs are pretty much idential to the Havoc...
Maybe they felt like it would be confusing having both ESC's listed...?
#6759
Tech Rookie
PLZ Help the people with real RC questions as you are the wisest
thankyou
#6761
The Evicerator
Yes they do!
We calibrate them the same as we do the 540 and 550 motors.
We calibrate them the same as we do the 540 and 550 motors.
#6763
The Evicerator
Not entirely sure yet... there's a decent chance of it though
#6764
Tech Elite
iTrader: (28)
Hey steve, my friend's havoc 17.5 system started acting funny today. Basically it was thermalling when it would hit around 115 degrees on the motor. In order to complete his main he had to take a can of compressed air and flip it upside down to freeze the can...then it thermalled after he crossed the line to finish the race.
Question is, he lost his recepit. The system hasnt really been out too long (120 day warranty right?)...if he brought this in to the Novak place to get checked out would there be any charged? Is it an issue that has been brought up? Seems like maybe he got a bad one or something. I had him make sure Lipo cut-off was off thinking it was the lipo-cut off voltage drop issue others have mentioned, but that wasnt the case.
Question is, he lost his recepit. The system hasnt really been out too long (120 day warranty right?)...if he brought this in to the Novak place to get checked out would there be any charged? Is it an issue that has been brought up? Seems like maybe he got a bad one or something. I had him make sure Lipo cut-off was off thinking it was the lipo-cut off voltage drop issue others have mentioned, but that wasnt the case.
#6765
Tech Master
iTrader: (3)
Hey steve, my friend's havoc 17.5 system started acting funny today. Basically it was thermalling when it would hit around 115 degrees on the motor. In order to complete his main he had to take a can of compressed air and flip it upside down to freeze the can...then it thermalled after he crossed the line to finish the race.
Question is, he lost his recepit. The system hasnt really been out too long (120 day warranty right?)...if he brought this in to the Novak place to get checked out would there be any charged? Is it an issue that has been brought up? Seems like maybe he got a bad one or something. I had him make sure Lipo cut-off was off thinking it was the lipo-cut off voltage drop issue others have mentioned, but that wasnt the case.
Question is, he lost his recepit. The system hasnt really been out too long (120 day warranty right?)...if he brought this in to the Novak place to get checked out would there be any charged? Is it an issue that has been brought up? Seems like maybe he got a bad one or something. I had him make sure Lipo cut-off was off thinking it was the lipo-cut off voltage drop issue others have mentioned, but that wasnt the case.
It may have been the speed control thermalling as well... Fan still have all its blades?