Team Associated TC4
Yodog, you have a sharp eye. I am so used to racing on dusty tracks with limited traction for off road that this is probably a habit. Also, I don't have much confidence with on road yet...... I have only raced on road TC for two days and no practice days are available due to a temporary drivers stand.
I have a solid axle and a ton of other parts......caster blocks, toe blocks etc.... I just need to figure out how to put the solid axle in the car.......well off to reading the manual......
I have a solid axle and a ton of other parts......caster blocks, toe blocks etc.... I just need to figure out how to put the solid axle in the car.......well off to reading the manual......
Another way to shave 12+ grams is to run carbon hinge pins, but you'll need to stay away from the walls....
Tech Elite
iTrader: (61)
Yodog, you have a sharp eye. I am so used to racing on dusty tracks with limited traction for off road that this is probably a habit. Also, I don't have much confidence with on road yet...... I have only raced on road TC for two days and no practice days are available due to a temporary drivers stand.
I have a solid axle and a ton of other parts......caster blocks, toe blocks etc.... I just need to figure out how to put the solid axle in the car.......well off to reading the manual......
I have a solid axle and a ton of other parts......caster blocks, toe blocks etc.... I just need to figure out how to put the solid axle in the car.......well off to reading the manual......
Crap!!!! >>>> reading the manual..... <<<< you don't need us any more!
Tech Elite
iTrader: (61)
SouthFloridaApp
Are you looking to race this?
ROAR REGIONAL CHAMPIONSHIP FEBRUARY 26/27/28
Good place to get some setup assist. LOT of fast guys!!
Need ROAR membership, if you don't have one, they should be able to a$$ite with that!
If you do share the experience with us!
Are you looking to race this?
ROAR REGIONAL CHAMPIONSHIP FEBRUARY 26/27/28
Good place to get some setup assist. LOT of fast guys!!
Need ROAR membership, if you don't have one, they should be able to a$$ite with that!
If you do share the experience with us!
Tech Elite
iTrader: (28)
Tech Elite
iTrader: (28)
Yodog, I tried getting those titanium hinge pins, but they were too expensive compared to carbon rods, and too hard to find...
I am open to all suggestions that remove all steel components out of the tc4, fragile or not !!! Time to measure some CF rods!
Got to go...Cheers....
I am open to all suggestions that remove all steel components out of the tc4, fragile or not !!! Time to measure some CF rods!
Got to go...Cheers....
I am going to the roar regionals. I will be most likely run three classes. 13.5 with my race-opt MTS T2, 17.5 with my factory team 17.5, and 21.5 with my TC4 club racer. If anyone is going come say hello.....My 21.5.....using the associated stock silver body.... 17.5 is a Mazda speed 6 white and somewhat clearish body...
I don't expect much as I need more time with my cars........tuning etc.....but it is always fun...
I don't expect much as I need more time with my cars........tuning etc.....but it is always fun...
Tech Addict
iTrader: (1)
Tech Champion
iTrader: (2)
Yodog, I tried getting those titanium hinge pins, but they were too expensive compared to carbon rods, and too hard to find...
I am open to all suggestions that remove all steel components out of the tc4, fragile or not !!! Time to measure some CF rods!
Got to go...Cheers....
I am open to all suggestions that remove all steel components out of the tc4, fragile or not !!! Time to measure some CF rods!
Got to go...Cheers....
Tech Regular
iTrader: (5)
I am going to the roar regionals. I will be most likely run three classes. 13.5 with my race-opt MTS T2, 17.5 with my factory team 17.5, and 21.5 with my TC4 club racer. If anyone is going come say hello.....My 21.5.....using the associated stock silver body.... 17.5 is a Mazda speed 6 white and somewhat clearish body...
I don't expect much as I need more time with my cars........tuning etc.....but it is always fun...
I don't expect much as I need more time with my cars........tuning etc.....but it is always fun...
Ralph
Tech Elite
iTrader: (61)
RC Tech FL thread for the ROAR race.
http://www.rctech.net/forum/florida-...6-27-28-a.html
Link to the track
http://valkariarc.com/
This maybe on LiveRC. HOPE it will be!!!
http://www.rctech.net/forum/florida-...6-27-28-a.html
Link to the track
http://valkariarc.com/
This maybe on LiveRC. HOPE it will be!!!
Carbon Rods(lifetime supply $25) and Nylon droop screws are ordered; time to work on the heavy shocks....
Tech Elite
iTrader: (2)
Anybody considering this and wasting a case of good beer worth of dough, remember that the shear strength of carbon fiber rod is about 1/20 that of stainless. It's probably strong enough to make a very light shelf queen. Just don't drop it.
Carbon rods are good in tension or compression, not side-bend shear.
Carbon rods are good in tension or compression, not side-bend shear.