Tekin RS/RS PRO on 1s Lipo Q&A
#1142
Randy I didn't know where to post this so I'll go ahead and ask on this thread. Will Tekin ever make a speedo specifically for VTA racing? If not, why? Thanks
#1145
Randy,
You mentioned in the Duo 3.5 thread that 1s causes issues in the sensor port after hard hits. How can we check the voltage of the sensor port at home?
I sent my RSPro in for service back in july to check the sensor port and it still cuts out.
You mentioned in the Duo 3.5 thread that 1s causes issues in the sensor port after hard hits. How can we check the voltage of the sensor port at home?
I sent my RSPro in for service back in july to check the sensor port and it still cuts out.
#1147
#1148
Tech Elite
iTrader: (70)
I'm going to be running a RS Pro with TQ booster in 1/12. Should I stick with the Tekin cap or would something like this LRP setup be better? http://www.amainhobbies.com/product_...-48V-Capacitor
#1149
Tech Champion
iTrader: (34)
I'm going to be running a RS Pro with TQ booster in 1/12. Should I stick with the Tekin cap or would something like this LRP setup be better? http://www.amainhobbies.com/product_...-48V-Capacitor
#1150
I run a RS Pro, Tekin Gen2, Radiopost radio w/ a hitec servo in my 1/12. I have to use booster or life pack. My friend has the exact same but different servo (can't remember which) and a RS and does not need to use booster/life in his 1/12... We can't figure it out other then perhaps his servo is not pulling as much amps?
#1151
Tech Adept
ok so here is my problem. as the kick off to our on road is only a couple months away, I sit with 2 1s cars with no speedos I want a esc that wont need a booster/reciver pack and herd of a possability of tekin making one in the gen2. do i wait or no?
Last edited by zeestraten46; 06-18-2013 at 05:43 AM. Reason: typo
#1152
Rs no output voltage on a b c
Running tekin rs on 1s.. Have a Novak booster hooked from positive and negative on esc to receiver. Receiver switched off and booster on it powers up. Voltage on the pin of esc for positive and negative equal the voltage of the battery... Now here's my dilemma. When checking voltage on the output pins when u initially turn the esc on they jump up to 3 something volts... Then drop down to .54 volts on a b c posts... When throttle is applied the voltage drops to zero on abc but the positive and negative on esc are not affected... I'm sure someone has had this problem... Just curious what to do or if the esc is junk.... Used speedo, new booster and sensor wire....
#1153
Tech Champion
iTrader: (17)
Running tekin rs on 1s.. Have a Novak booster hooked from positive and negative on esc to receiver. Receiver switched off and booster on it powers up. Voltage on the pin of esc for positive and negative equal the voltage of the battery... Now here's my dilemma. When checking voltage on the output pins when u initially turn the esc on they jump up to 3 something volts... Then drop down to .54 volts on a b c posts... When throttle is applied the voltage drops to zero on abc but the positive and negative on esc are not affected... I'm sure someone has had this problem... Just curious what to do or if the esc is junk.... Used speedo, new booster and sensor wire....
#1154
Tech Regular
iTrader: (6)
New to 1 S And Looking for some Info
I have a Tekin RS I put it on 1 S mode with the hot wire.
Now do I need to unplug The Red Wire or no ,
Can I use the on / off switch or no
I know this is a Old info but info on 1s is very limited out here
I just don't want to ruin a new ESC
I have a Tekin RS I put it on 1 S mode with the hot wire.
Now do I need to unplug The Red Wire or no ,
Can I use the on / off switch or no
I know this is a Old info but info on 1s is very limited out here
I just don't want to ruin a new ESC
#1155
Hate to hijack a thread. I have a pro 1s I used last season. It was working no issues on my 7px. I traded that and cash for a M17.
I cannot (and been trying stuff for 3 hours) get the neutral to set. I hold the button for set up get the original jingle then it sits there. Will mot beep for neutral. I’ve tried to change the reverse back and forth a million times.
The servo works. Nothing for throttle. First three lights on left side of esc are blinking fast when I turn on the esc.
anyway if anyone knows of something to help please let me know.
I cannot (and been trying stuff for 3 hours) get the neutral to set. I hold the button for set up get the original jingle then it sits there. Will mot beep for neutral. I’ve tried to change the reverse back and forth a million times.
The servo works. Nothing for throttle. First three lights on left side of esc are blinking fast when I turn on the esc.
anyway if anyone knows of something to help please let me know.