Tamiya TRF415
Tech Master
iTrader: (12)
Hey does anyone know if the MRE airscoop is available and if so what is the code for it please.
Thanks
Addam
Thanks
Addam
Originally Posted by TRFMAD
Thanks Proceed5 for you help again mate,
Hey chris that chassis look's great mate, how much does he charge and will he ship worldwide.
Thanks Mate
Addam
Hey chris that chassis look's great mate, how much does he charge and will he ship worldwide.
Thanks Mate
Addam
There $15 Canadian
and yes he will ship world wide.
check out his web page he makes tones of rc dekelz
www.dekelz.com
Originally Posted by TRFMAD
Hey does anyone know if the MRE airscoop is available and if so what is the code for it please.
Thanks
Addam
Thanks
Addam
Don't think the Airscoop is released yet.
Regards
Tech Rookie
FAb/Ed ... Cheers guys
Will definatly come over and say hello...Ed I used a speed6 for the first time at Maritime last week and it had so much grip it was trying to dig itself a hole!!! I am going to try a few different wings tonight and see if I can lessen it up a bit as I prefer my car a bit looser (at the rear) - dont really want to change the car set-up as it was ok with my previous moorespeed M - but that shell is dead!! The speed6 is strong as an ox too, hardly a mark from the usual banger racing last thursday.
As we are showing each other what we look like!! this is me, as you can see I have a great imagination - straight lines courtesy of Mr. Orion Internals!!!!
See you on Sunday
Martin
Will definatly come over and say hello...Ed I used a speed6 for the first time at Maritime last week and it had so much grip it was trying to dig itself a hole!!! I am going to try a few different wings tonight and see if I can lessen it up a bit as I prefer my car a bit looser (at the rear) - dont really want to change the car set-up as it was ok with my previous moorespeed M - but that shell is dead!! The speed6 is strong as an ox too, hardly a mark from the usual banger racing last thursday.
As we are showing each other what we look like!! this is me, as you can see I have a great imagination - straight lines courtesy of Mr. Orion Internals!!!!
See you on Sunday
Martin
Tech Initiate
Originally Posted by tamiyarcracer
MRE belts now or stock belts?
Originally Posted by chris_morrison_
Its laminated vinyl and the material was tested by the owner of www.dekelz.com on his xray for a 6 month outdoor season.
This is the first one he has done for the mre so it needs a little fine tuning
i applied it with Windex and a heat gun total time to apply 10min.
This is the first one he has done for the mre so it needs a little fine tuning
i applied it with Windex and a heat gun total time to apply 10min.
its a laminated vinyl that has the same glue that stickers have so its removable but not reusable
chris morrison
chris morrison
Tech Champion
iTrader: (4)
Originally Posted by coolsteel
Hi,
I am a newbie of MRE, just want to ask Q about the change of roll center:
If I add some shims (eg. 1mm) below the Rear suspension mounts (both in the rear), then the roll center will change, right? Then what happen to the rear traction if I add more to lift up the rear suspension mounts? The car will has more / less roll at the rear??? More grip at the rear??
Thanks in advance!
I am a newbie of MRE, just want to ask Q about the change of roll center:
If I add some shims (eg. 1mm) below the Rear suspension mounts (both in the rear), then the roll center will change, right? Then what happen to the rear traction if I add more to lift up the rear suspension mounts? The car will has more / less roll at the rear??? More grip at the rear??
Thanks in advance!
As a rule of thumb, this generally takes away grip.
HiH
Ed
Can anyone inform me, what the differences between the MRE and MSXX ?
Thanks
Thanks
Tech Champion
iTrader: (4)
hehe.... jsut wanted to point something out to everyone in here... this thread (17,227 posts) now has more posts than Schumacher Corner (17,204 and covering all Schuie cars), the RDX thread (10,118), and even the XXX-s (13,725) and TC3 (11,091) threads are well behind...
Looks like this is the seond most popular thread, behind the 1/12 forum (23,334)... got to say something about the 415 line of cars...
Anyone guess I have a lot of time on my hands at work today??
Looks like this is the seond most popular thread, behind the 1/12 forum (23,334)... got to say something about the 415 line of cars...
Anyone guess I have a lot of time on my hands at work today??
and the 12th scale form covers every 12th scale car
Tech Master
iTrader: (12)
GGGGGGOOOOOO 415
Tech Master
iTrader: (12)
415 RULES
Tech Addict
TryHard, Without you, I don't think this thread can go this LONG!
Is this works in 415 MRE?
http://shopping.rcmodel.hk/product_...roducts_id=5151 thanks
Is this works in 415 MRE?
http://shopping.rcmodel.hk/product_...roducts_id=5151 thanks
hi all
i tryed to order a tamiya damper air remover from rcmodel but ive just recieved email saying they havent got one and asked would i take the ride rp 700 one instead
is the rp 700 suitable for 1/10 shocks?
can anyone shed some light on this?
cheers
i tryed to order a tamiya damper air remover from rcmodel but ive just recieved email saying they havent got one and asked would i take the ride rp 700 one instead
is the rp 700 suitable for 1/10 shocks?
can anyone shed some light on this?
cheers
Last edited by pug 205 gti; 01-25-2007 at 03:44 AM.