Tamiya TB-03
#706
Tech Initiate
DAMPER and INsert!
I have question about the TRF damper?
Is this the same? performance wise!
http://www.rcmart.com/catalog/rc-dam...8-p-26673.html
http://www.rcmart.com/catalog/rc-dam...2-p-23733.html
Also which tire insert should i use for low grip parking lot?
Thanks!
Is this the same? performance wise!
http://www.rcmart.com/catalog/rc-dam...8-p-26673.html
http://www.rcmart.com/catalog/rc-dam...2-p-23733.html
Also which tire insert should i use for low grip parking lot?
Thanks!
#707
Tech Initiate
This is the hopups that I will be purchasing for my car, I am a new tamiya user so Im not sure if I miss something or not. did I miss a part which is really important?
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
#708
Tech Lord
iTrader: (26)
This is the hopups that I will be purchasing for my car, I am a new tamiya user so Im not sure if I miss something or not. did I miss a part which is really important?
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
#709
The only thing I can think of is a servo saver. The kit servo saver is junk. I assume you are good on springs, tires, and shock oil options?
#710
Tech Addict
iTrader: (3)
I have question about the TRF damper?
Is this the same? performance wise!
http://www.rcmart.com/catalog/rc-dam...8-p-26673.html
http://www.rcmart.com/catalog/rc-dam...2-p-23733.html
Also which tire insert should i use for low grip parking lot?
Thanks!
Is this the same? performance wise!
http://www.rcmart.com/catalog/rc-dam...8-p-26673.html
http://www.rcmart.com/catalog/rc-dam...2-p-23733.html
Also which tire insert should i use for low grip parking lot?
Thanks!
#711
I just ordered a TB03(58409) and a Novak Havoc 13.5 esc and motor. I bought it to use on asphalt and carpet. The owner of the LHS told me I can't fit it with foam tires without extensive changes because the foams hit the knuckle. Is there any other option if I want to run foams on it? I intend to run rubber mostly anyway but I would like the option to switch.
I use LRP VTEC foams on several cars and i don't have a problem with that. Normally the knuckle is turning in just parallel to the foam tire while steering so the space between will rest just the same.
The only problem i had on my trf 414M was that the inner rim touched the upper end of the tie rod attached to the knuckle. I solved this with some Dremel work on the inside of the rim. Just taking off 1mm on the inside removing the sharp 90° edge.
#712
Tech Initiate
This is the hopups that I will be purchasing for my car, I am a new tamiya user so Im not sure if I miss something or not. did I miss a part which is really important?
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
x Tamiya (#54056) TB-03 Aluminum Differential Joint Set
x Tamiya (#54067) TB-03 Suspension Mount (1XA)
x Tamiya (#54072) TB-03 Aluminum Suspension Mount (1D)
x Tamiya (#54073) TB-03 Aluminum Suspension Mount (1E)
x Tamiya (#54076) TB-03 Wheel Axles
x Tamiya (#54095) TB-03 Racing Steering Set
x Tamiya (#54097) TB-03 Carbon Steering Link
x Tamiya (#54125) TB03D Direct Coupling
x Tamiya (#54151) TB-03 High Precision Bearing Holder
x Tamiya (#53570) Clamp Type Alu. Wheel Hub (4mm Thick)
x Tamiya (#53907) 5x8mm Alu. Hex Ball Connector
x Tamiya (#53932) Alu. Suspension Mount Spacer (0.5mm)
x Tamiya (#53933) Alu. Suspension Mount Spacer (1mm)
x Tamiya (#54078) 44mm Swing Shafts
x Tamiya (#53724) 46mm LIGHTWEIGHT For TB Evo.IV
x Tamiya (#53539) Ø5.5mm Alu. Spacer Set
x Tamiya (#42137) Competition O-Rings For Oil Dampers
x Tamiya (#84008) TRF Sp Damper H Coating (BK)
#713
I just can't imagine where the foams should hit the knuckle. Which foams are you looking for / by using which foams will this appear?
I use LRP VTEC foams on several cars and i don't have a problem with that. Normally the knuckle is turning in just parallel to the foam tire while steering so the space between will rest just the same.
The only problem i had on my trf 414M was that the inner rim touched the upper end of the tie rod attached to the knuckle. I solved this with some Dremel work on the inside of the rim. Just taking off 1mm on the inside removing the sharp 90° edge.
I use LRP VTEC foams on several cars and i don't have a problem with that. Normally the knuckle is turning in just parallel to the foam tire while steering so the space between will rest just the same.
The only problem i had on my trf 414M was that the inner rim touched the upper end of the tie rod attached to the knuckle. I solved this with some Dremel work on the inside of the rim. Just taking off 1mm on the inside removing the sharp 90° edge.
#719
It's not a SS screw kit, but Tony's Screws are good stuff.
This is the kit I got for TA05v2... http://www.tonysscrews.com/product.s...&categoryId=60
It's a 136 piece kit for the TA05.
There is also a 180 piece kit for the TA05MS... http://www.tonysscrews.com/product.s...&categoryId=60
I also have various RC Screwz SS screw kits from other models; so far I have been able to avoid using the phillips heads
Last edited by slakr; 08-12-2009 at 07:57 PM.
#720
Tech Champion
iTrader: (108)
If anyones looking. I have some leftover hopups and parts for the TB03.
NIP Oneway
1 run old Spool
A couple NIP Diff and Spool/oneway gear sets
A bunch of composite suspension mounts XA etc
NIP stock composite outdrives (2 packs of 4 outdrives)
Drop me a PM if interested
NIP Oneway
1 run old Spool
A couple NIP Diff and Spool/oneway gear sets
A bunch of composite suspension mounts XA etc
NIP stock composite outdrives (2 packs of 4 outdrives)
Drop me a PM if interested