Team Losi JRXS Type-R
Tech Champion
iTrader: (1)
I have always liked the look of the GM but have heard mixed feelings about it from drivers and the importer and also the weight is quite high. Here in oz there is talk of a low weight limit for next year (1425g) which will make balancing the chassis on rubber tyres difficult with my current gear. For that reason I am looking at changing ESC and servo to recover enough weight for better balance until a better chassis layout is ready. This is something to be wary of with a speedy that weights almost 100g without wires!
Finally got to watch that vid and it looks like he was having a ball! Kinda like a mod car in a 10.5 field! I can understand parts of his setup when you hear the tyre noise! There was an incredible amount of grip on that track.
Finally got to watch that vid and it looks like he was having a ball! Kinda like a mod car in a 10.5 field! I can understand parts of his setup when you hear the tyre noise! There was an incredible amount of grip on that track.
Yes, weighth is a disadvantage, 95g with wires is quite a lot. But what one can do...
Anyway, JRXS looks great on track.
Anyway, JRXS looks great on track.
Tech Champion
iTrader: (73)
1. Groskamp Jilles - Tamiya/Speedpassion - 2 pts
2. Rheinard Marc - Tamiya/Speedpassion - 4
3. Völker Ronald - Yokomo/LRP - 4
4. Hönigl Hubert - Tamiya/LRP - 7
5. Wilck Viktor - Tamiya/Speedpassion - 8
6. Prümper Yannic - Tamiya/Speedpassion - 9
7. Graversen Steen - Kyosho/Team Orion - 12
8. Krapp Christopher - Kyosho/Team Orion - 13
9. Urbain Lucas - Losi/GM Racing - 13
10.Hagberg Alexander - Xray/LRP - 15
2. Rheinard Marc - Tamiya/Speedpassion - 4
3. Völker Ronald - Yokomo/LRP - 4
4. Hönigl Hubert - Tamiya/LRP - 7
5. Wilck Viktor - Tamiya/Speedpassion - 8
6. Prümper Yannic - Tamiya/Speedpassion - 9
7. Graversen Steen - Kyosho/Team Orion - 12
8. Krapp Christopher - Kyosho/Team Orion - 13
9. Urbain Lucas - Losi/GM Racing - 13
10.Hagberg Alexander - Xray/LRP - 15
Tech Elite
iTrader: (46)
LCD pin falling out
Hey guys
Recently im having a problem keeping my lcd's together. I thought all i needed was some new ones since the current ones had lots of use on them. I replaced both parts and also the parts that hold them together. I got 2 runs and the pin came out again. Has anyone else had this problem? Are you using better shrink tubing? Any other ideas what could be causing this?
Recently im having a problem keeping my lcd's together. I thought all i needed was some new ones since the current ones had lots of use on them. I replaced both parts and also the parts that hold them together. I got 2 runs and the pin came out again. Has anyone else had this problem? Are you using better shrink tubing? Any other ideas what could be causing this?
Company Representative
iTrader: (6)
1. Groskamp Jilles - Tamiya/Speedpassion - 2 pts
2. Rheinard Marc - Tamiya/Speedpassion - 4
3. Völker Ronald - Yokomo/LRP - 4
4. Hönigl Hubert - Tamiya/LRP - 7
5. Wilck Viktor - Tamiya/Speedpassion - 8
6. Prümper Yannic - Tamiya/Speedpassion - 9
7. Graversen Steen - Kyosho/Team Orion - 12
8. Krapp Christopher - Kyosho/Team Orion - 13
9. Urbain Lucas - Losi/GM Racing - 13
10.Hagberg Alexander - Xray/LRP - 15
2. Rheinard Marc - Tamiya/Speedpassion - 4
3. Völker Ronald - Yokomo/LRP - 4
4. Hönigl Hubert - Tamiya/LRP - 7
5. Wilck Viktor - Tamiya/Speedpassion - 8
6. Prümper Yannic - Tamiya/Speedpassion - 9
7. Graversen Steen - Kyosho/Team Orion - 12
8. Krapp Christopher - Kyosho/Team Orion - 13
9. Urbain Lucas - Losi/GM Racing - 13
10.Hagberg Alexander - Xray/LRP - 15
Is that Urbain Lucas tire came off at 2nd lap of 3rd leg?
Last edited by SweepRacingUSA; 08-02-2009 at 01:39 PM.
Company Representative
iTrader: (6)
Hey guys
Recently im having a problem keeping my lcd's together. I thought all i needed was some new ones since the current ones had lots of use on them. I replaced both parts and also the parts that hold them together. I got 2 runs and the pin came out again. Has anyone else had this problem? Are you using better shrink tubing? Any other ideas what could be causing this?
Recently im having a problem keeping my lcd's together. I thought all i needed was some new ones since the current ones had lots of use on them. I replaced both parts and also the parts that hold them together. I got 2 runs and the pin came out again. Has anyone else had this problem? Are you using better shrink tubing? Any other ideas what could be causing this?
Tech Champion
iTrader: (17)
Looks like it: posted from the official scorring site.
He was 7th the first heat, 6th the second and 8th with a breakdown on the 3rd running only 9 laps. Total time put him down to 9th.
He was 7th the first heat, 6th the second and 8th with a breakdown on the 3rd running only 9 laps. Total time put him down to 9th.
Tech Elite
iTrader: (46)
Company Representative
iTrader: (6)
I agree, or shrink wrap didnt shrinked enough and it shakes around?
in other hand if a shrink is too long it will bind ball bearing shield or it can cause broken castor block.
Make sure you are using the correct size pin. I thought I broke another joint piece because of the spool, but it turned out I accidently put a wheel hex pin in it and was too short. Lasted a couple weeks before it fell out.
Tech Elite
iTrader: (267)
Hey guys I got some SMC 40c hard pack lipos and they don't fit the lipo tray. They are barely too big to fit inside the lip. Does any one use thee and have any tricks? What lipos are you guys using that do fit?
Super Moderator
iTrader: (239)
Tech Elite
iTrader: (124)