Team Losi JRXS Type-R
#2446
Tech Lord
iTrader: (32)
If you plan on running the 13.5, I hope you've got some BIIIIIIIG pinion gears. There's not much hope of running anything lower than 108T spur. A 100T with 41T pinion was about a mile off. :-O
I guess I'm just a gimp. The PRS thing is working fine now, I just made the slot longer with the dremel. I guess I could have filed the pin too. Now I've just got a snug fit so that the layshaft can't move side to side at all. I checked everything mentioned here and still no luck.
Mounting a GTB in this sucker has been interesting. I ended up having to do it like the picture of Todd's car. Otherwise, the belt is in the way and the ESC is hanging off the side too much.
I guess I'm just a gimp. The PRS thing is working fine now, I just made the slot longer with the dremel. I guess I could have filed the pin too. Now I've just got a snug fit so that the layshaft can't move side to side at all. I checked everything mentioned here and still no luck.
Mounting a GTB in this sucker has been interesting. I ended up having to do it like the picture of Todd's car. Otherwise, the belt is in the way and the ESC is hanging off the side too much.
#2449
I hope the handling far out ways some of the little things about the car I do not like. I am not crazy about the battery tray in this car. I like the old one with two screws better. Installing electronics on this thing is really tight and stuff does over hang the chassis. I run a GTX and it still over hangs the chassis a little. I am probably going to purchase a micro Spektrum receiver in the future for I don't like how the regular one hangs off the chassis.
I do have to say I had no issues building it though and thought it went together well. I also like how the up limit adjustment brackets are now part of the arms. The diff tubes and indrives are really nice. Diffs will be so much easier to work on now since it is four screws and it is out.
The transponder worked out fine for me even though I don't have ears on it anymore. It just fits on the chassis in back of the roll center brace with the velcro I normally used to install it.
I only need to change my wires on my speedo and put the thing on a setup station and all will be done. I only wish I had somewhere to run it now!!
I do have to say I had no issues building it though and thought it went together well. I also like how the up limit adjustment brackets are now part of the arms. The diff tubes and indrives are really nice. Diffs will be so much easier to work on now since it is four screws and it is out.
The transponder worked out fine for me even though I don't have ears on it anymore. It just fits on the chassis in back of the roll center brace with the velcro I normally used to install it.
I only need to change my wires on my speedo and put the thing on a setup station and all will be done. I only wish I had somewhere to run it now!!
#2450
Originally Posted by flameoutgarrett
anyone else get a spare shock bladder? cause im looking at 4 built shocks and 1 bladder.....and im 99.2% positive that i have them all in there
#2451
Tech Lord
iTrader: (32)
The SLR was dead, so I had to grab my wife's crappy camera which seems to struggle with, well, anything related to creating digital photographs in focus. Anyway, here's the completed monster with 13.5, GTB and Carbon LiPo. We're DEFINITELY going to need a weighted LiPo tray, I don't see how we can make weight without putting it on the outside of the chassis.
#2453
For those that have built their cars...
how hard will it be to remove bearings for cleaning. is it a 30 min marathon, followed by a complete rebuild, or is it a 5 min easy job?
How good are the bearings? I was going to get a set of ceramics when they are available. Any thoughts?
how hard will it be to remove bearings for cleaning. is it a 30 min marathon, followed by a complete rebuild, or is it a 5 min easy job?
How good are the bearings? I was going to get a set of ceramics when they are available. Any thoughts?
#2454
Tech Master
iTrader: (15)
Originally Posted by $$$...
Hey Keith, great looking car you got there... hanging out for them to make it down here. Just wondering, I thought the car had the "new" front camber mod? does the kit come with both?
Camber mod is included.. but I dont run it. Im not sure if anyone does on foam???
Spur is 126 or 128 PRS... (only two i have)
Swaybars are direct fit.
KB
#2455
Tech Master
iTrader: (15)
Originally Posted by Yeti35
I hope the handling far out ways some of the little things about the car I do not like. I am not crazy about the battery tray in this car. I like the old one with two screws better.
Whaaaaa 4 screws...
actually, you only need 2. The lip in the front will hold it in just fine. Personally, i run all 4, but i think Kevin Hebert runs just 2.
#2456
so i take it everyone has enjoyed the build process of the car and we can read some results and how it went on the track... also how were the instructions, i read on here someone said they might be close to how xray has there instructions. If thats the case then that is very nice to see.
#2457
Tech Legend
iTrader: (51)
Join Date: Sep 2001
Location: Castle Mamba Max Pro. Feel its power!!!!!!!!!!
Posts: 21,220
Trader Rating: 51 (100%+)
Originally Posted by syndr0me
The SLR was dead, so I had to grab my wife's crappy camera which seems to struggle with, well, anything related to creating digital photographs in focus. Anyway, here's the completed monster with 13.5, GTB and Carbon LiPo. We're DEFINITELY going to need a weighted LiPo tray, I don't see how we can make weight without putting it on the outside of the chassis.
Be interesting to see what you think of it after you have a chance to run it. Does look pretty cool.
#2458
Tech Elite
iTrader: (95)
I will post pics of mine when I get the chance. I mounted my Sphere on it's side. I think it will be fine that way.
Keith B...you don't think anyone is running the camber mod on carpet? Why do you say that? What's it for? Hodge, care to weigh in here?
Also, if anyone needs a PRS adapter in blue w/extra 128 spur (2 spurs total) give me a shout. A friend of mine is getting out and gave one to me.
Blake
Keith B...you don't think anyone is running the camber mod on carpet? Why do you say that? What's it for? Hodge, care to weigh in here?
Also, if anyone needs a PRS adapter in blue w/extra 128 spur (2 spurs total) give me a shout. A friend of mine is getting out and gave one to me.
Blake
Last edited by dr_hfuhuhurr; 03-24-2007 at 06:35 AM.
#2459
Originally Posted by dr_hfuhuhurr
Also, if anyone needs a PRS adapter in blue w/extra 128 spur (2 spurs total) give me a shout. A friend of mine is getting out and gave one to me.
Blake
Blake
Thanks,
#2460
Also has anyone noticed alot of play in the rear arms? Mine seem to have alot of play front to back.
Later,
Later,