|
PW, Any clamping hexes (front and rear) for the SC5M soon? Especially in black!
|
Are the foams for the 2wd front smoothies a little undersized? When I glues up my tires, the foams do not seem to fill the tire very well..
|
I was wondering if anyone has tried the rips in the black compound. They are out of green like I use on the rear of the car and was thinking the black or blue. Was thinking of grabbing the golds for indoor clay if they were any good just to try.
Also how are their dirt-tech inserts? I want to try closed foam inserts this time since the open cell foams are breaking down quick |
Originally Posted by Fabulous
(Post 14198469)
PW, Any clamping hexes (front and rear) for the SC5M soon? Especially in black!
Are the foams for the 2wd front smoothies a little undersized? When I glues up my tires, the foams do not seem to fill the tire very well.. I was wondering if anyone has tried the rips in the black compound. They are out of green like I use on the rear of the car and was thinking the black or blue. Was thinking of grabbing the golds for indoor clay if they were any good just to try. Also how are their dirt-tech inserts? I want to try closed foam inserts this time since the open cell foams are breaking down quick |
problem corrected no fault of the product..
|
Serration may be worn out on the nut? I wore one out on a 1/10 scale buggy and it kept slightly backing off.
|
I'm thinking the Same try get the nuts that have the serrated finish and nylon liner
Oh and keep a eye on the serrated edge they wear out |
Originally Posted by one8updragracer
(Post 14201636)
Has anyone had problems with the buggy wheels not holding the hex area tight enough.
Tried some double dees pre mounts indoor last week, tires worked great did exactly what I expected but when I went to take them off one of them was slipping. I had to run a screwdriver through the outdrive to hold the axle so I could get the wheel nut off. Running A tekno with the closed end wheel nuts. I noticed there is definitely less "meat" in the wheel hex area compared to my AKA and Proline wheels I normally run. Like you have alluded to, sounds like the close-ended wheel nuts are not allowing the wheel nut to fully engage into the wheel. Our more current wheels shouldn't have this issue and I would recommend using an open-ended wheel nut for those older wheels. |
PW, is it possible to do a run of 1/10th stadium Dirt Webs in black compound? I would really appreciate it.
|
Originally Posted by jneezie3000
(Post 14203775)
PW, is it possible to do a run of 1/10th stadium Dirt Webs in black compound? I would really appreciate it.
Just put some WD40 on some unmounted greens and bag them over night :blush:;) |
https://scontent-mia1-1.xx.fbcdn.net...4a&oe=56A2B56C
Keep up to date with JConcepts at the 2015 IFMAR Worlds where new products are being covered daily - Click Here |
S2 Body
PW, any eta on the S2's availability?
|
Originally Posted by Beau S
(Post 14210622)
PW, any eta on the S2's availability?
|
Originally Posted by PW
(Post 14210502)
https://scontent-mia1-1.xx.fbcdn.net...4a&oe=56A2B56C
Keep up to date with JConcepts at the 2015 IFMAR Worlds where new products are being covered daily - Click Here |
any chance on more color choices for 4mm nut #2089-2090?
maybe green or plain aluminum in the future? thanks |
| All times are GMT -7. It is currently 01:46 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.