R/C Tech Forums - JConcepts Thread

I'm thinking Bar Codes front and rear on buggy and truck and either Bar Codes or Pressure Points for SCT. Green or Blue rear and maybe orange front.

During the nitro race last month it was super grooved up, but they didn't sweep/clean the track for 1/10th scale, so I ran 3D's in buggy and PP's in SCT. For the Clash, we will be brooming the track for 10th scale :nod:.

I'm bringing my Dustbuster to the clash this year.

J_Bone

08-06-2012 12:49 PM

never mind.....it was answered.

Wicked-Wayz

08-06-2012 04:22 PM

Paul, do you guys have any rims that fit the Tamiya 201 buggy?

Peace Aaron(W-W)

PW	08-07-2012 05:57 AM

Quote:

Originally Posted by Wicked-Wayz (Post 11062754)

Paul, do you guys have any rims that fit the Tamiya 201 buggy?

Peace Aaron(W-W)

Nothing purposely made for the 201. There might be some cross-over possibilities, but not sure.

Wicked-Wayz

08-07-2012 07:10 AM

Ok thank you for the response.

Peace Aaron(W-W)

ECH	08-07-2012 12:53 PM

anybody know when are the black jackets 1/8 buggy tires coming out .

Ostach24

08-07-2012 12:55 PM

Any plans or eta for an Eco finnisher body?

ANiznik

08-07-2012 01:08 PM

Quote:

Originally Posted by Wicked-Wayz (Post 11062754)

Paul, do you guys have any rims that fit the Tamiya 201 buggy?

Peace Aaron(W-W)

the rulux wheels work great on the 201! u just need the 3/16 front axles that are a factory option!

PW	08-07-2012 01:10 PM

Quote:

Originally Posted by ECH (Post 11066286)

anybody know when are the black jackets 1/8 buggy tires coming out .

We had a delay; so we are planning on having production Black Jackets for the JConcepts Clash in Sept.

Quote:

Any plans or eta for an Eco finnisher body?

It's on the list, but most likely in the Fall.

DirtRacer68

08-07-2012 01:22 PM

Is there any pics of the new sway bar kit for the SC10?

ECH	08-07-2012 01:29 PM

Quote:

Originally Posted by PW (Post 11066332)

We had a delay; so we are planning on having production Black Jackets for the JConcepts Clash in Sept.

It's on the list, but most likely in the Fall.

thanks Chad at ech

1Fastpede

08-07-2012 04:40 PM

is there any air vent holes in the RC8.2e finnisher body?

PW	08-08-2012 05:23 AM

Quote:

Originally Posted by 1Fastpede (Post 11067077)

is there any air vent holes in the RC8.2e finnisher body?

There are large exhaust cut outs for letting hot air out of the back, but no vents in the front. However, there is room on the front side-pods to cut out if needed.

Jeckler

08-08-2012 05:34 AM

For the SC10 hexes, the problem is that once they're stripped, going to a 2mm longer screw doesn't help, as you still only have 2mm of thread to work with. If you "upgrade" from the start, then it might help. Like dizzy1 though, the first one I installed stripped before it could clamp onto the axle.
I re-tapped mine to 2-56 and used 1/4" screws. No need to drill for the tap, but I did have to drill the untapped side for the screw to go in. I also compressed the hex with a pair of pliers while installing.

Wicked-Wayz

08-08-2012 08:46 AM

Quote:

Originally Posted by ANiznik (Post 11066327)

the rulux wheels work great on the 201! u just need the 3/16 front axles that are a factory option!

Thanks for the info, do any of the other 1/10th rims work? Do I have to do anything to the rears to work?

Peace Aaron(W-W)

All times are GMT -7. It is currently 07:53 PM.

Page 351 of 719