86LikesHpi Pro 4
07-28-2004, 07:18 PM
#6511
Woodward
Welcome to the Inner Sanctum
What you describe is correct, as it is not a diff up front, it is a one-way. It allows drive to the front wheels (and is locked like a locked diff) but when drive is removed, it allows the front wheels to freewheel, like a pushbike crank.
Welcome to the Inner Sanctum
What you describe is correct, as it is not a diff up front, it is a one-way. It allows drive to the front wheels (and is locked like a locked diff) but when drive is removed, it allows the front wheels to freewheel, like a pushbike crank.
07-28-2004, 07:24 PM
#6512
Tech Rookie
Ahhhh. I understand now. Thank-you
07-28-2004, 09:52 PM
#6514
Tech Master
Originally posted by Super Steve
pretty pro 4 body...
No fancy job on this one
just plain old one color jobby!
pretty pro 4 body...
No fancy job on this one
just plain old one color jobby!
What color is that?
07-28-2004, 10:46 PM
#6516
Hey guys, need a setup for the Pro 4 for a (bumpy from what I have heard) parking lot track. I am heading to the Hitec race and plan on taking the Pro 4 along with my Mi2 (Mi2= front diff, Pro 4=One Way) and I have been running the car on carpet. Any help would be appreciated.
07-28-2004, 10:48 PM
#6517
Tech Master
How's the traction? I found out that the STOCK setup works excellent.
P.S.
At my local parking lot track, it's pretty bumpy in the straight.
I run 5mm droop all around. 40wt all around. Coppers in front/Silvers in back. 5mm ride height all around. Take Off CS-22
P.S.
At my local parking lot track, it's pretty bumpy in the straight.
I run 5mm droop all around. 40wt all around. Coppers in front/Silvers in back. 5mm ride height all around. Take Off CS-22
Last edited by DOMOisCOOL; 07-28-2004 at 10:54 PM.
07-28-2004, 11:02 PM
#6518
Registered User
Tech Racing Pro4 Chassis
07-28-2004, 11:26 PM
#6519
Originally posted by robk
You may also want to add the little collars DuBro sells. You can slide them on the bar until they stop. Tighten the grub screw and they will stay in place, keeping the bar from going sideways when it flexes.
The collars are used to hold the wheels on rc airplanes, or to hold together 2 z bends for a servo linkage (think RC10 from 1985)
You may also want to add the little collars DuBro sells. You can slide them on the bar until they stop. Tighten the grub screw and they will stay in place, keeping the bar from going sideways when it flexes.
The collars are used to hold the wheels on rc airplanes, or to hold together 2 z bends for a servo linkage (think RC10 from 1985)
I saw a pic of Hara's car with some collars on the sway bars but not on his most recent car... any ideas they were purple anodised?
07-28-2004, 11:31 PM
#6520
Originally posted by DOMOisCOOL
How's the traction? I found out that the STOCK setup works excellent.
P.S.
At my local parking lot track, it's pretty bumpy in the straight.
I run 5mm droop all around. 40wt all around. Coppers in front/Silvers in back. 5mm ride height all around. Take Off CS-22
How's the traction? I found out that the STOCK setup works excellent.
P.S.
At my local parking lot track, it's pretty bumpy in the straight.
I run 5mm droop all around. 40wt all around. Coppers in front/Silvers in back. 5mm ride height all around. Take Off CS-22
07-28-2004, 11:56 PM
#6521
Originally posted by acutts
Does anyone have the part number for the little dubro collars??
I saw a pic of Hara's car with some collars on the sway bars but not on his most recent car... any ideas they were purple anodised?
Does anyone have the part number for the little dubro collars??
I saw a pic of Hara's car with some collars on the sway bars but not on his most recent car... any ideas they were purple anodised?
07-29-2004, 06:50 AM
#6523
Can I use Associated Composite CVD Bones for TC3 with HPI PRO4?
http://www2.towerhobbies.com/cgi-bin...?&I=LXNZ89&P=7
http://www2.towerhobbies.com/cgi-bin...?&I=LXNZ89&P=7
Last edited by X-Garage; 07-29-2004 at 07:28 AM.
07-29-2004, 06:55 AM
#6524
Originally posted by X-Garage
Can I use Associated Composite CVD Bones for TC3 with HPI PRO4?
http://www2.towerhobbies.com/cgi-bin...?&I=LXNZ89&P=7
Can I use Associated Composite CVD Bones for TC3 with HPI PRO4?
http://www2.towerhobbies.com/cgi-bin...?&I=LXNZ89&P=7
07-29-2004, 07:09 AM
#6525
Originally posted by X2
yep
yep