Xray T3 2012
#2521
hi guys
anybody could point me to a good set up sheet for the following conditions: low -medium traction, asphalt, 40 feet straight, indoor, 13.5T boosted?
thanks in advance.
anybody could point me to a good set up sheet for the following conditions: low -medium traction, asphalt, 40 feet straight, indoor, 13.5T boosted?
thanks in advance.
#2522
Tech Rookie
Dogbone wear
Anyone ever experienced with the wear on the rear dogbone as shown in the attached picture?
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
#2523
Tech Elite
iTrader: (8)
Anyone ever experienced with the wear on the rear dogbone as shown in the attached picture?
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
#2525
Last edited by Skiddins; 05-21-2012 at 09:57 AM.
#2526
R/C Tech Elite Member
iTrader: (66)
Slightly larger track, but might be of use;
http://piez0r.com/Skiddins/Xray%20Setup%20Sheets/Carpet%20Setups/T3%2712-Newbury%28A%29-4-5-12.pdf
http://piez0r.com/Skiddins/Xray%20Setup%20Sheets/Carpet%20Setups/T3%2712-Newbury%28A%29-4-5-12.pdf
#2527
Original link should now be fixed
#2528
Tech Rookie
#2529
Thank you very much!
#2530
Tech Adept
iTrader: (3)
Anyone ever experienced with the wear on the rear dogbone as shown in the attached picture?
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
Kit: T3 2012
Rear Gear Diff with stock Alu outdrive
Dogbone: 50mm
Rear Toe: Inboard 3 Degree Toe in
I never find this problem before on any other previous xray kit. It is obvious that the 'ball' of the dogbone rubs against the inner wall of the Alu outdrive. The option spring steel gear outdrive is slotted, can changing the spring steel one improve the problem?
Thanks very much!
Simon
#2531
Tech Rookie
i remember i saw some where else saying the bone would cause binding with the outdrive if the rear camber is above 1.5. I always run 1.5 or above camber so thats the reason i run 50mm bone
#2533
Tech Champion
iTrader: (38)
Anyone know when RC America is supposed to get their next shipment of T3s?
Also why would RCA charge $19 shipping for 4 small parts to my LHS. It makes already expensive parts VERY expensive. Hopefully they don't charge shipping on each individual shipment since they didn't send everything together.
Also why would RCA charge $19 shipping for 4 small parts to my LHS. It makes already expensive parts VERY expensive. Hopefully they don't charge shipping on each individual shipment since they didn't send everything together.
#2534
Tech Elite
iTrader: (15)
Anyone know when RC America is supposed to get their next shipment of T3s?
Also why would RCA charge $19 shipping for 4 small parts to my LHS. It makes already expensive parts VERY expensive. Hopefully they don't charge shipping on each individual shipment since they didn't send everything together.
Also why would RCA charge $19 shipping for 4 small parts to my LHS. It makes already expensive parts VERY expensive. Hopefully they don't charge shipping on each individual shipment since they didn't send everything together.
Their shipping is very reasonable. Maybe the hobby shop had it upgraded to second day air or something?