U.S. Vintage Trans-Am Racing
Tech Fanatic
iTrader: (54)
USVTA logo decals.
Thanks to Doug from Squarehead Designs for the layout.
Printed on Clear Vinyl. Red, White and Blue.
$8 per sheet.
Also, check out : http://www.rctech.net/forum/r-c-item...am-decals.html for more VTA decals.
If interested, send me an e-mail @ [email protected]
Thanks.
Carl
Thanks to Doug from Squarehead Designs for the layout.
Printed on Clear Vinyl. Red, White and Blue.
$8 per sheet.
Also, check out : http://www.rctech.net/forum/r-c-item...am-decals.html for more VTA decals.
If interested, send me an e-mail @ [email protected]
Thanks.
Carl
Tech Elite
iTrader: (9)
Good thing you aren't running on a old Windows computer or all those fonts would have used up your available memory. (I'm an IT nerd )
Tech Adept
I'll try and get you an order over the weekend that will include #'s 67 in the that font with the bolder type.
Thanks again,
Lynn
Tech Champion
iTrader: (30)
For USGT - is there a battery limit? Max mah?? Or just any roar approved battery pack?
I have a set of VTA tires i bought for the first USVTA nats. I ran them at the second one and took a few years off. They've been stored in the closet but not in a plastic bag. They have plenty of tread left but feel a bit dry. Should I pick up a fresh set for this year's nats?
Tech Elite
iTrader: (10)
I have a set of VTA tires i bought for the first USVTA nats. I ran them at the second one and took a few years off. They've been stored in the closet but not in a plastic bag. They have plenty of tread left but feel a bit dry. Should I pick up a fresh set for this year's nats?
Tech Champion
iTrader: (2)
Chassis Specification:
Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
Weight Specification:
4wd 1450g weight Fwd 1400g weight
Body Specifications:
Any 190mm or 200mm body. Body can be any body that is NOT on the ROAR T2 body list. NO Trucks
Any "SCALE" molded wings can be used. Lexan wings 10mm maximum height / side dam height
Scale type race liveries encouraged
Tire & Wheel Specifications:
Tires-Any treaded (non slick) non belted rubber tire available 24 or 26mm. Removing belts from belted tires is not allowed. Must used a non-molded (ex. open cell foam) insert or no insert. Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Wheels- Any 24 or 26mm spoke (non-dish) type wheel
Ride Height Specification:
Minimum ride height is 5mm.
Motor Specifications:
21.5 + 2s lipo batteries No tuning rotors, must use OEM rotor 12.3-12.5mm
Approved ESCs:
ESC ROAR approved spec software or USVTA list
Race Specification:
6 minute qualifiers
8 minute mains
Battery Specifications:
ROAR approved hard case batteries
Tech Champion
iTrader: (30)
Saw all that, but is there a limit like usvta?? Or could i run a 5400 pack?
USGT Class Rules and Specifications
Chassis Specification:
Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
Weight Specification:
4wd 1450g weight Fwd 1400g weight
Body Specifications:
Any 190mm or 200mm body. Body can be any body that is NOT on the ROAR T2 body list. NO Trucks
Any "SCALE" molded wings can be used. Lexan wings 10mm maximum height / side dam height
Scale type race liveries encouraged
Tire & Wheel Specifications:
Tires-Any treaded (non slick) non belted rubber tire available 24 or 26mm. Removing belts from belted tires is not allowed. Must used a non-molded (ex. open cell foam) insert or no insert. Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Wheels- Any 24 or 26mm spoke (non-dish) type wheel
Ride Height Specification:
Minimum ride height is 5mm.
Motor Specifications:
21.5 + 2s lipo batteries No tuning rotors, must use OEM rotor 12.3-12.5mm
Approved ESCs:
ESC ROAR approved spec software or USVTA list
Race Specification:
6 minute qualifiers
8 minute mains
Battery Specifications:
ROAR approved hard case batteries
Chassis Specification:
Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
Weight Specification:
4wd 1450g weight Fwd 1400g weight
Body Specifications:
Any 190mm or 200mm body. Body can be any body that is NOT on the ROAR T2 body list. NO Trucks
Any "SCALE" molded wings can be used. Lexan wings 10mm maximum height / side dam height
Scale type race liveries encouraged
Tire & Wheel Specifications:
Tires-Any treaded (non slick) non belted rubber tire available 24 or 26mm. Removing belts from belted tires is not allowed. Must used a non-molded (ex. open cell foam) insert or no insert. Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
Wheels- Any 24 or 26mm spoke (non-dish) type wheel
Ride Height Specification:
Minimum ride height is 5mm.
Motor Specifications:
21.5 + 2s lipo batteries No tuning rotors, must use OEM rotor 12.3-12.5mm
Approved ESCs:
ESC ROAR approved spec software or USVTA list
Race Specification:
6 minute qualifiers
8 minute mains
Battery Specifications:
ROAR approved hard case batteries
Tech Champion
iTrader: (2)
humm...I would say its ok, due to Rob being very specific with the rules....but wait for him to chime in on here or USGT...Im running 5000 Reedy for both classes
Tech Champion
iTrader: (32)
Join Date: Aug 2001
Location: In a land of mini-mighty mental giants
Posts: 8,854
Trader Rating: 32 (100%+)
As far as what was written into the rules and talked about its any ROAR approved 2cell lipo for USGT.....VTA has the 5000mah Cap. Not that you really need anything more then a 3800 really....but its there if you want it.
ran my first VTA race, super fun, has the novak 25.5 epoxy stator been added to the approved list for this class.
Tech Elite
iTrader: (73)
Our Local race track [OVRCCC] has adjusted our VTA requirments to allow the racers an easier way to keep racing
Saturday we had 9 VTA racers and we ran the ALL in the Main
Currently we allow 21.5, and the VTA required Speedo's
NO gear ratio limit,
We are discussing the possibly of allowing ROAR "TC SPEC" speedos
our racers feel they are very limited in Speedos so they are in favor of allowing more speedos in VTA as long as they meet the 'Blinky mode'
Now let the beatings begin!!
Saturday we had 9 VTA racers and we ran the ALL in the Main
Currently we allow 21.5, and the VTA required Speedo's
NO gear ratio limit,
We are discussing the possibly of allowing ROAR "TC SPEC" speedos
our racers feel they are very limited in Speedos so they are in favor of allowing more speedos in VTA as long as they meet the 'Blinky mode'
Now let the beatings begin!!
Our Local race track [OVRCCC] has adjusted our VTA requirments to allow the racers an easier way to keep racing
Saturday we had 9 VTA racers and we ran the ALL in the Main
Currently we allow 21.5, and the VTA required Speedo's
NO gear ratio limit,
We are discussing the possibly of allowing ROAR "TC SPEC" speedos
our racers feel they are very limited in Speedos so they are in favor of allowing more speedos in VTA as long as they meet the 'Blinky mode'
Now let the beatings begin!!
Saturday we had 9 VTA racers and we ran the ALL in the Main
Currently we allow 21.5, and the VTA required Speedo's
NO gear ratio limit,
We are discussing the possibly of allowing ROAR "TC SPEC" speedos
our racers feel they are very limited in Speedos so they are in favor of allowing more speedos in VTA as long as they meet the 'Blinky mode'
Now let the beatings begin!!
It's still basically VTA and I'm assuming none of your racers plan on being part of a VTA sanctioned race nor is the club planning on promoting a sanctioned event.
I am curious though. "To allow the racers an easier way to keep racing"...What does that mean ?? I'm guessing EVERYBODY already has 21.5 motors?? Just a reminder and something you may not have thought about. As the speed increases, certain costs due to wear will increase exponentially. Tires in particular will wear out much faster and therefore each racer will spend more in the long run.