Team Losi JRXS Type-R
#8581
#8582
#8583
Tech Adept
iTrader: (8)
Doesn't suprise me though... I just realized after running my R for a couple months that my kit came with 41t pulleys instead of 42's! I thought the spool was making my car loose in the rear... (41t in the rear and 42 up front. Can you say underdrive?)
#8584
Tech Elite
iTrader: (11)
I just got a spool pulley couple weeks ago and there wasn't anything but the pulley in the bag...
Doesn't suprise me though... I just realized after running my R for a couple months that my kit came with 41t pulleys instead of 42's! I thought the spool was making my car loose in the rear... (41t in the rear and 42 up front. Can you say underdrive?)
Doesn't suprise me though... I just realized after running my R for a couple months that my kit came with 41t pulleys instead of 42's! I thought the spool was making my car loose in the rear... (41t in the rear and 42 up front. Can you say underdrive?)
#8585
Tech Elite
iTrader: (46)
Thanks guys, my cars were pretty good, i was very happy with the foam runs, mis judged the track a bit for the mains, and ended up with a lot of push, so the sweeper was a killer. Rubber i had the tq, but the race wasn't so great in terms of my car staying on the track...oh well on to the next one.
For those interested, played with a spool setup for rubber this race, il post it up.
Morris, usually just loosen the upper deck and flatten the chassis on a board, hold and tighten,
For those interested, played with a spool setup for rubber this race, il post it up.
Morris, usually just loosen the upper deck and flatten the chassis on a board, hold and tighten,
No sway bars? Whats up with that? By the way, great running this past weekend. You and Jason sure do know how to keep the excitement going...WOW
#8586
shreff, larry, mike,
will any of you be at the novak race???
will any of you be at the novak race???
#8587
I will not be there, too many races too close together. Gonna do the grand slam series and the birds.
Rui..thanks...i had the bars off to get some roll in the car...for 360 i always run bars
Rui..thanks...i had the bars off to get some roll in the car...for 360 i always run bars
#8588
damn....that was fast...
i put your iic setup on my car, it is pretty good.....planning on leaving it for the novak....,, unless you ave a better idea...
matt
i put your iic setup on my car, it is pretty good.....planning on leaving it for the novak....,, unless you ave a better idea...
matt
#8589
#8590
#8591
After a few nights of reading I just read the entire thread with a skip during the part when everyone was waiting "2 weeks" for the kit at the beginning of 07. Lots of great information. By far the most repeated question is, "What is the link to get a spur gear adaptor?"
I have a kit coming and looking forward to hitting the rug again now we got a track close. I figured I would start with Mike's setup and work from there. Before the previous track pulled the on road track out I had a JRXS Pro and like it alot if this car has even more steering but keeps that same consistent feel I'm going to like it alot.
I have a kit coming and looking forward to hitting the rug again now we got a track close. I figured I would start with Mike's setup and work from there. Before the previous track pulled the on road track out I had a JRXS Pro and like it alot if this car has even more steering but keeps that same consistent feel I'm going to like it alot.
#8592
roll center
when adjusting the low roll center upwards using the (0.30) shims where should I place the shims in the four corners of the rear pivot blocks or just in the inner or the outer pivot blocks
thanks
thanks
#8594
You want to shim up all 4 corners of the rear pivot blocks. If you were to just do the inner or outer blocks you would be doing pro or anti squat. Something you may see on a rubber setup may be front kickup or antidive. That would be where you only shim 2 of the 4 corners of the pivot blocks, anti dive being the inner front pivots and kickup the outer front pivots.
#8595
Is it better to run a couple of fans on the motor in the stock locations or get a heatsink that has a fan mounted on it like 3racing's fan/heatsink combo? Any opinions?