Tekin RS ESC sensored
Tech Elite
iTrader: (20)
Did it feel like a lot of negative exponential on the throttle or was the motor just flat coming off of the corners? Three is linear but if you like a more positive expo feel, you could go to 4 or 5. If it's just a flat feeling motor, some other set-up changes may be in order.
i have the nutral band with set at 20.
Tech Elite
iTrader: (20)
i'll change it to 5 and see how it felfs
Randy is 100% right, i had EXACT same thing happen with mine, after close inspection found with my tq booster, the red wire came undone on the esc,so it looked as if everything was sorta working, but the lower voltage wouldnt let me get power/chime etc...dont know what booster ur running, but with my tq, i have the leave the esc switch ON and than the booster ON, but i hear novak esc off, etc...check to be sure u have right combo...definatlly booster
If the RS won't run the motor with the swtich on your Voltage Cutoff isn't set right.
When programming the ESC, I have the voltage cutoff set to "OFF". Is that a problem? I've been running it this way since last August without any issue. It is pretty easy to determine when the voltage is getting low and shutting off the voltage with my trigger finger.
What is a correct Voltage Cutoff setting for 1S LiPo with a TQ boost? How about with a receiver pack?
I kind'a like it the way it is, because I only have to turn on/off one switch.
Tech Elite
iTrader: (49)
Thanks for the reply, Randy. Once again demonstrating that Tekin has great support for it's customers.
What is a correct Voltage Cutoff setting for 1S LiPo with a TQ boost? How about with a receiver pack?
I kind'a like it the way it is, because I only have to turn on/off one switch.
What is a correct Voltage Cutoff setting for 1S LiPo with a TQ boost? How about with a receiver pack?
I kind'a like it the way it is, because I only have to turn on/off one switch.
He Phil,
You're going to buy a Tekin?
Can't you keep up with Marcel Pinkster
Updates are free and you can download it from the Tekin site. www.teamtekin.com
15,3 by Richard and still the nr 1 is Marcel.
So soon you can bead them as you have your Tekin
You're going to buy a Tekin?
Can't you keep up with Marcel Pinkster
Updates are free and you can download it from the Tekin site. www.teamtekin.com
15,3 by Richard and still the nr 1 is Marcel.
So soon you can bead them as you have your Tekin
i will try it , but i thnk the laptop at a track wil pi55 me off a little
Richard took out the Tekin and put the GM120 back in on sunday as he was struggling with it
if i dont like it then i will see how the SXX Stock spec goes , i gotta respect the things for being idiot proof (i am an idiot)
does any one have a good set up for 13.5 carpet with a 30m straight and quite quick flowing corners ???
what do i do for gearing ?? with the SPX i got 30/78 on an Xray T3
Tekin RS Pro / 6.5BL / Durango DEX410
what profile should I use for the above?
have v203 software
racing at this indoor venue
what profile should I use for the above?
have v203 software
racing at this indoor venue
+ YouTube Video | |
this may mean we will have a new software to run on macs.
http://www.watoday.com.au/digital-li...0128-mz84.html
http://www.watoday.com.au/digital-li...0128-mz84.html
Last edited by niznai; 01-28-2010 at 07:29 AM.
Tech Master
well i spoke with Eric mulder and he was importing some so i told him to post me one
i will try it , but i thnk the laptop at a track wil pi55 me off a little
Richard took out the Tekin and put the GM120 back in on sunday as he was struggling with it
if i dont like it then i will see how the SXX Stock spec goes , i gotta respect the things for being idiot proof (i am an idiot)
does any one have a good set up for 13.5 carpet with a 30m straight and quite quick flowing corners ???
what do i do for gearing ?? with the SPX i got 30/78 on an Xray T3
i will try it , but i thnk the laptop at a track wil pi55 me off a little
Richard took out the Tekin and put the GM120 back in on sunday as he was struggling with it
if i dont like it then i will see how the SXX Stock spec goes , i gotta respect the things for being idiot proof (i am an idiot)
does any one have a good set up for 13.5 carpet with a 30m straight and quite quick flowing corners ???
what do i do for gearing ?? with the SPX i got 30/78 on an Xray T3
Both work fine.
Soon I have my speedpassion V3 motor and than I can try the setups myself and how they run.
With the V203, you are also fast with not a good setup.
Tech Elite
iTrader: (29)
still cannot get 203 on my labtop, i have a new dell Core 2 duo, windows vista, labtop...when hotwire come on says something like the esc settings exceed the hotwire capability's or such. is it just a matter of it simply wont work on certain pc's? i deleted hidden file etc...