CEFX 2010 - A new Evolution.
01-29-2011, 12:08 PM
#676
RIP EVO 
Very few people left to fight with the bowing issue ...
even designer dissepeared from the forum lol
Very few people left to fight with the bowing issue ...
even designer dissepeared from the forum lol
Last edited by yokemad; 01-29-2011 at 05:25 PM.
01-29-2011, 01:41 PM
#677
01-29-2011, 05:24 PM
#678
double post
01-29-2011, 05:31 PM
#679
I was talking about the forum 
almost no international support left!
Even after several months has past there is still no response from Josh about Bowing issue!
Do you think I had asked for a lot? If so sorry!
almost no international support left!
Even after several months has past there is still no response from Josh about Bowing issue!
Do you think I had asked for a lot? If so sorry!
01-29-2011, 05:33 PM
#680
Yeah Josh is running a CEFX at snowbirds
It really was more of a comment on that I did offer as much support as possible for the CEFX Evo on setup and on anything else that I could help on.
Best regards,
James
It really was more of a comment on that I did offer as much support as possible for the CEFX Evo on setup and on anything else that I could help on.
Best regards,
James
01-30-2011, 04:01 AM
#681
I know James ,You were always here for help and support Thank you but you also gave up and I'm not blaming you...
All I want is to see him in this thread to tell us about that famous issue and If there is any remedy for that or not as a designer of the evo ...
we all know How busy He is but come on, it would only takes his few minutes to check whats going on here and I believe he is aware of the issues anyway...
I like my Evo but ending up a banana shape chassis end of every race is a bit heartbreaking
All I want is to see him in this thread to tell us about that famous issue and If there is any remedy for that or not as a designer of the evo ...
we all know How busy He is but come on, it would only takes his few minutes to check whats going on here and I believe he is aware of the issues anyway...
I like my Evo but ending up a banana shape chassis end of every race is a bit heartbreaking
01-31-2011, 08:19 PM
#682
Josh-
Great runs at the birds, hope you are getting over the illness. I'm home now and sick too.
Care to share with us how you setup your Futaba charger for charging lipo? Didn't take a close look as I was always busy prepping my own cars but were you charging your 2S packs with it too?
Thanks!
Great runs at the birds, hope you are getting over the illness. I'm home now and sick too.
Care to share with us how you setup your Futaba charger for charging lipo? Didn't take a close look as I was always busy prepping my own cars but were you charging your 2S packs with it too?
Thanks!
02-01-2011, 03:54 AM
#686
Glad he sorted out that bowing issue with that conventional solution
Please put them on sale Josh
Please put them on sale Josh
I really like it though, makes everything else so much simpler
02-01-2011, 06:14 AM
#688
Looks like he eliminated most of the TOP parts other than maybe the roll center mounts and possibly the bearing cams. Looks like far more Tamiya parts now. I like the Tamiya dual post steering and the servo mounted horizontally. So much more room for the rest of the electronics when you mount a low profile servo like that. Very cool. Car looked great on the track.
02-01-2011, 06:26 AM
#689
I would have to say that is an updated version of the Evolution. Josh run his with Tamiya parts for a while now. It looks like there is a small carbon plate under the motor mounts, It would help with bowing issue as well as the new top deck.
02-01-2011, 01:00 PM
#690
Tech Adept
For me this car looks very different from the evo.
I think there is a new main chassis, top deck and the tamiya steering. Looks like the TOP suspension can be used anyway aswell as the drive train-?-
I think there is a new main chassis, top deck and the tamiya steering. Looks like the TOP suspension can be used anyway aswell as the drive train-?-