NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
+1
81020340 81020350 81020360 are the 2s version in 3 colors. the 1s version is not on the approved list. is this a clerical error or something else?
81020340 81020350 81020360 are the 2s version in 3 colors. the 1s version is not on the approved list. is this a clerical error or something else?
Tech Regular
iTrader: (11)
Cobra, used the Reedy 4.0 motor (TC ON), the fast track;
The track is hot (+ / - 50C) and air temp + / - 35C.
My ESC V3.1 (new)!
FDR 8.6 (One CSO). motor was ok! 80 to 90C, max.
But the ESC stoped, it disarmed by overheat protection.
Setup in race was 0º boost and 0º Turbo, for 5 minutes to finish the race.
I tried using 5 points Boost (start 30k and Finish 60.000) and thus was up to 4 minutes (overheat protection).
I can not use this set?
Motor Reedy first generation with Reedy 6500 65C lipos. Endbell is a Zero points.
Tks.
The track is hot (+ / - 50C) and air temp + / - 35C.
My ESC V3.1 (new)!
FDR 8.6 (One CSO). motor was ok! 80 to 90C, max.
But the ESC stoped, it disarmed by overheat protection.
Setup in race was 0º boost and 0º Turbo, for 5 minutes to finish the race.
I tried using 5 points Boost (start 30k and Finish 60.000) and thus was up to 4 minutes (overheat protection).
I can not use this set?
Motor Reedy first generation with Reedy 6500 65C lipos. Endbell is a Zero points.
Tks.
I'm not surprised the speedy shut it self down.
You may have been fortunate it did, as it saved a motor from going up in smoke.
Angelo,
congrats for getting Atsushi Hara onto the Hobbywing team! I wish all of you good luck! (everyone can now see, that the hard work like yours really pays off)
congrats for getting Atsushi Hara onto the Hobbywing team! I wish all of you good luck! (everyone can now see, that the hard work like yours really pays off)
I dont believe that a customer needs to wait 2 weeks for a reply i believe 24hours max .
We need to work harder because other esc manufacturers or brands will start catching up and i will not allow that to happen i must be atleast 2-3 years ahead in all levels.
Once again thank you for your kind words
Angelo
Im sure its a typo as i know it has been approved because i know the software is approved for all v3 and 2.1 series esc's ill check with roar next monday-tuesday.
Cobra, used the Reedy 4.0 motor (TC ON), the fast track;
The track is hot (+ / - 50C) and air temp + / - 35C.
My ESC V3.1 (new)!
FDR 8.6 (One CSO). motor was ok! 80 to 90C, max.
But the ESC stoped, it disarmed by overheat protection.
Setup in race was 0º boost and 0º Turbo, for 5 minutes to finish the race.
I tried using 5 points Boost (start 30k and Finish 60.000) and thus was up to 4 minutes (overheat protection).
I can not use this set?
Motor Reedy first generation with Reedy 6500 65C lipos. Endbell is a Zero points.
Tks.
The track is hot (+ / - 50C) and air temp + / - 35C.
My ESC V3.1 (new)!
FDR 8.6 (One CSO). motor was ok! 80 to 90C, max.
But the ESC stoped, it disarmed by overheat protection.
Setup in race was 0º boost and 0º Turbo, for 5 minutes to finish the race.
I tried using 5 points Boost (start 30k and Finish 60.000) and thus was up to 4 minutes (overheat protection).
I can not use this set?
Motor Reedy first generation with Reedy 6500 65C lipos. Endbell is a Zero points.
Tks.
Tech Initiate
Tks Cobra... sent my setup sheet.
Tech Elite
iTrader: (43)
running 17.5 blinky will i see any differentce in running a just stock vs stock spec 3.1 or the competition v3.1? also i say on the hw website the lcd box had stopped production? is there somthing new ?
The other escs you mentioned are part of the new generation v3 and can run zero timing but also boost and turbo timing applications.
If you are running on blinky and always running blinky stick with the justock which can run down to a 8.5t motor if turbo is needed and lower turn motors the others mentioned will work fine with zero and turbo .The v3 also runs different software with more adjustability and options and is fitted with a cnc aluminium case for better heat dissipation.v3.1 120 amp competition only.
There is a new lcd program box which can run both version and also has a built in lipo voltage checker.
Send me an email if you want to know more or need a setup to begin with i will be vety happy to help you out. [email protected]
Tech Elite
iTrader: (43)
All 3 are top escs the justock is zero timing and no other software can be loaded it is also part of the v2 family of esc like the 120 amp ,60 amp and xtreme stock which csn run boost timing and turbo etc.
The other escs you mentioned are part of the new generation v3 and can run zero timing but also boost and turbo timing applications.
If you are running on blinky and always running blinky stick with the justock which can run down to a 8.5t motor if turbo is needed and lower turn motors the others mentioned will work fine with zero and turbo .The v3 also runs different software with more adjustability and options and is fitted with a cnc aluminium case for better heat dissipation.v3.1 120 amp competition only.
There is a new lcd program box which can run both version and also has a built in lipo voltage checker.
Send me an email if you want to know more or need a setup to begin with i will be vety happy to help you out. [email protected]
The other escs you mentioned are part of the new generation v3 and can run zero timing but also boost and turbo timing applications.
If you are running on blinky and always running blinky stick with the justock which can run down to a 8.5t motor if turbo is needed and lower turn motors the others mentioned will work fine with zero and turbo .The v3 also runs different software with more adjustability and options and is fitted with a cnc aluminium case for better heat dissipation.v3.1 120 amp competition only.
There is a new lcd program box which can run both version and also has a built in lipo voltage checker.
Send me an email if you want to know more or need a setup to begin with i will be vety happy to help you out. [email protected]
The v3 series esc's are the worlds most powerful and smoothest .The software is also the most advanced.
Tech Fanatic
iTrader: (27)
That being said, it's a very small difference in feel on the carpet. I've used pretty much every HW ESC, from the Justock to the 60a, 90a, 120a, 120v3, 120v3.1, Stock Spec v3.1.
ANY of them are awesome in blinky. For mod, I greatly prefer the v3 firmware though.
Tech Master
iTrader: (5)
You dont need to run the ESC fan for 17.5 and 13.5 it just doesnt get hot enough, so you can use the fan port to plug your motor fan in. This port is also high voltage so you can run 8.4 volt fans with no issues.
Beth. (happy hobbywing customer)
Tech Elite
iTrader: (43)
thanks for the replys. I think ill go with the stock spec 3.1 over the just stock then.
Tech Fanatic
iTrader: (27)
The stock spec is awesome. I run one on my blinky car. Awesome ESC.