Serpent S411
#6031
Tech Apprentice
#6032
Tech Elite
iTrader: (58)
Had a good run with the car over the weekend, we normally run the car pretty still, 550wt shock oil and ride reds, but we softened up the car over the weekend, 450wt and the new ride short white springs, car felt pretty good, the best it had felt in a long while, also ran a gear diff in the front, seemed to work good also, the new ride short springs fit the shocks really good.
Rhys
Rhys
#6033
Tech Elite
iTrader: (24)
I ran the same event as crabboy over the weekend but in stock. I came 3rd. Overall, my first podium at a big event. The new short ride red springs work well. I ran slightly wider/longer wheelbase than normal as the track had a very bumpy undulating surface. My car had phenomenal corner speed. Poor motor/speedy choice let me down in the end.
#6034
Tech Elite
iTrader: (101)
I ran the same event as crabboy over the weekend but in stock. I came 3rd. Overall, my first podium at a big event. The new short ride red springs work well. I ran slightly wider/longer wheelbase than normal as the track had a very bumpy undulating surface. My car had phenomenal corner speed. Poor motor/speedy choice let me down in the end.
Had a good run with the car over the weekend, we normally run the car pretty still, 550wt shock oil and ride reds, but we softened up the car over the weekend, 450wt and the new ride short white springs, car felt pretty good, the best it had felt in a long while, also ran a gear diff in the front, seemed to work good also, the new ride short springs fit the shocks really good.
Rhys
Rhys
Steve
#6037
Tech Elite
iTrader: (24)
Race Report.
We had the Australian National Titles at the Little Hampton track in South Australia this past weekend. This is a Very large 200 plus metre Nitro track with lots of off camber corners and a large uphill sweeper and downhill section that really catches out a poorly set up car. There was a small turnout due to Various reasons but those who turned up to race were still a tough crowd and the title was not going to be an easy affair. I had a battle with 4 Xrays for Tq. Current AOC stock champion Scott K took the TQ every round with the New T4 '14. I managed 5 x 2nds and a 3rd to wrap up second on the grid. Local fast guys James, David and Sam(Xray) all close behind.
The finals were a tough affair as 3rd and 4th had bolted in new motors for the finals and with it new found pace. I had been running the same(all be it strong) motor all weekend and was really feeling it in the last couple of minutes. The luxury of disposable income.
Scott was the class act of the field and drove off in all 3 finals leaving the rest of us to battle it out. I had an action packed 1st final and a racing incident in a fight for second with James had both of us rolled to the outfield and the pack drove past. I managed to fight back to 4th that race. Scott 1st, Sam 2nd, Trevor 3rd.
Second final was a much cleaner affair and i managed to take home 2nd. Results were Scott 1st, Me 2nd Sam 3rd. With 2nd and 3rd still up for grabs in the last final it was a very hectic first few laps with driver changes from 2nd thru to 5th. I had a roll over on the 1st straight and had to fight back from 5th. It was a neck and neck battle with Sam for second place over the last 5 laps and i ended up coming 3rd by 0.6 of a second and thus losing 2nd on the podium.
This was my first podium at a big event so i was still very pleased with the outcome.
Overall results were
Scott K 1st Xray T4'14 / Orca VXX / Orion Vst2 / LRP Lipo
Sam B 2nd Xray T4'13 / Hw V3.1 / Orion Vst2 / SMC lipo
Ben K 3rd Erxy 2.0 / Orion R10 Pro / Trinity D3.5 / SMC lipo
Thanks to Jay from WalterRC
Set up sheet for the event.
We had the Australian National Titles at the Little Hampton track in South Australia this past weekend. This is a Very large 200 plus metre Nitro track with lots of off camber corners and a large uphill sweeper and downhill section that really catches out a poorly set up car. There was a small turnout due to Various reasons but those who turned up to race were still a tough crowd and the title was not going to be an easy affair. I had a battle with 4 Xrays for Tq. Current AOC stock champion Scott K took the TQ every round with the New T4 '14. I managed 5 x 2nds and a 3rd to wrap up second on the grid. Local fast guys James, David and Sam(Xray) all close behind.
The finals were a tough affair as 3rd and 4th had bolted in new motors for the finals and with it new found pace. I had been running the same(all be it strong) motor all weekend and was really feeling it in the last couple of minutes. The luxury of disposable income.
Scott was the class act of the field and drove off in all 3 finals leaving the rest of us to battle it out. I had an action packed 1st final and a racing incident in a fight for second with James had both of us rolled to the outfield and the pack drove past. I managed to fight back to 4th that race. Scott 1st, Sam 2nd, Trevor 3rd.
Second final was a much cleaner affair and i managed to take home 2nd. Results were Scott 1st, Me 2nd Sam 3rd. With 2nd and 3rd still up for grabs in the last final it was a very hectic first few laps with driver changes from 2nd thru to 5th. I had a roll over on the 1st straight and had to fight back from 5th. It was a neck and neck battle with Sam for second place over the last 5 laps and i ended up coming 3rd by 0.6 of a second and thus losing 2nd on the podium.
This was my first podium at a big event so i was still very pleased with the outcome.
Overall results were
Scott K 1st Xray T4'14 / Orca VXX / Orion Vst2 / LRP Lipo
Sam B 2nd Xray T4'13 / Hw V3.1 / Orion Vst2 / SMC lipo
Ben K 3rd Erxy 2.0 / Orion R10 Pro / Trinity D3.5 / SMC lipo
Thanks to Jay from WalterRC
Set up sheet for the event.
Last edited by Benzaah; 11-24-2013 at 04:34 PM.
#6038
Anyone tried 3-hole vs. 4-hole pistons on carpet. It seems that Xray drivers always use 4-hole @1.2 mm nowadays.
#6039
Tech Regular
iTrader: (11)
i recently took bearing out of my s411 to clean . they would spin freely then she i put the diff bearing in i noticed as i tightened down the bulkhead screws the diff would not spin freely. has anyone else ever noticed this? my idea to fix is maybe a 1 mm shim under bulk head to give bearing some room and keep it from clamping down on bearing.. what do you guys think?
also i have a friend looking to buy a another s411 the let me know if anyone has one for sale thanks!!!
also i have a friend looking to buy a another s411 the let me know if anyone has one for sale thanks!!!
Last edited by buckeye dan; 11-25-2013 at 06:20 AM.
#6042
Tech Master
iTrader: (64)
Ok, sounds good. I just posting a listing on the for sale thread...
http://www.rctech.net/forum/r-c-item...l#post12756142
http://www.rctech.net/forum/r-c-item...l#post12756142
#6043
Race Report.
We had the Australian National Titles at the Little Hampton track in South Australia this past weekend. This is a Very large 200 plus metre Nitro track with lots of off camber corners and a large uphill sweeper and downhill section that really catches out a poorly set up car. There was a small turnout due to Various reasons but those who turned up to race were still a tough crowd and the title was not going to be an easy affair. I had a battle with 4 Xrays for Tq. Current AOC stock champion Scott K took the TQ every round with the New T4 '14. I managed 5 x 2nds and a 3rd to wrap up second on the grid. Local fast guys James, David and Sam(Xray) all close behind.
The finals were a tough affair as 3rd and 4th had bolted in new motors for the finals and with it new found pace. I had been running the same(all be it strong) motor all weekend and was really feeling it in the last couple of minutes. The luxury of disposable income.
Scott was the class act of the field and drove off in all 3 finals leaving the rest of us to battle it out. I had an action packed 1st final and a racing incident in a fight for second with James had both of us rolled to the outfield and the pack drove past. I managed to fight back to 4th that race. Scott 1st, Sam 2nd, Trevor 3rd.
Second final was a much cleaner affair and i managed to take home 2nd. Results were Scott 1st, Me 2nd Sam 3rd. With 2nd and 3rd still up for grabs in the last final it was a very hectic first few laps with driver changes from 2nd thru to 5th. I had a roll over on the 1st straight and had to fight back from 5th. It was a neck and neck battle with Sam for second place over the last 5 laps and i ended up coming 3rd by 0.6 of a second and thus losing 2nd on the podium.
This was my first podium at a big event so i was still very pleased with the outcome.
Overall results were
Scott K 1st Xray T4'14 / Orca VXX / Orion Vst2 / LRP Lipo
Sam B 2nd Xray T4'13 / Hw V3.1 / Orion Vst2 / SMC lipo
Ben K 3rd Erxy 2.0 / Orion R10 Pro / Trinity D3.5 / SMC lipo
Thanks to Jay from WalterRC
Set up sheet for the event.
We had the Australian National Titles at the Little Hampton track in South Australia this past weekend. This is a Very large 200 plus metre Nitro track with lots of off camber corners and a large uphill sweeper and downhill section that really catches out a poorly set up car. There was a small turnout due to Various reasons but those who turned up to race were still a tough crowd and the title was not going to be an easy affair. I had a battle with 4 Xrays for Tq. Current AOC stock champion Scott K took the TQ every round with the New T4 '14. I managed 5 x 2nds and a 3rd to wrap up second on the grid. Local fast guys James, David and Sam(Xray) all close behind.
The finals were a tough affair as 3rd and 4th had bolted in new motors for the finals and with it new found pace. I had been running the same(all be it strong) motor all weekend and was really feeling it in the last couple of minutes. The luxury of disposable income.
Scott was the class act of the field and drove off in all 3 finals leaving the rest of us to battle it out. I had an action packed 1st final and a racing incident in a fight for second with James had both of us rolled to the outfield and the pack drove past. I managed to fight back to 4th that race. Scott 1st, Sam 2nd, Trevor 3rd.
Second final was a much cleaner affair and i managed to take home 2nd. Results were Scott 1st, Me 2nd Sam 3rd. With 2nd and 3rd still up for grabs in the last final it was a very hectic first few laps with driver changes from 2nd thru to 5th. I had a roll over on the 1st straight and had to fight back from 5th. It was a neck and neck battle with Sam for second place over the last 5 laps and i ended up coming 3rd by 0.6 of a second and thus losing 2nd on the podium.
This was my first podium at a big event so i was still very pleased with the outcome.
Overall results were
Scott K 1st Xray T4'14 / Orca VXX / Orion Vst2 / LRP Lipo
Sam B 2nd Xray T4'13 / Hw V3.1 / Orion Vst2 / SMC lipo
Ben K 3rd Erxy 2.0 / Orion R10 Pro / Trinity D3.5 / SMC lipo
Thanks to Jay from WalterRC
Set up sheet for the event.
#6044
i recently took bearing out of my s411 to clean . they would spin freely then she i put the diff bearing in i noticed as i tightened down the bulkhead screws the diff would not spin freely. has anyone else ever noticed this? my idea to fix is maybe a 1 mm shim under bulk head to give bearing some room and keep it from clamping down on bearing.. what do you guys think?
also i have a friend looking to buy a another s411 the let me know if anyone has one for sale thanks!!!
also i have a friend looking to buy a another s411 the let me know if anyone has one for sale thanks!!!
#6045
Tech Regular
iTrader: (11)
I tried 4 holes a while back but seem to end up on 3 hole all the time. I think if you run the 4 hole the feel will give too much front end and the car already rotates on the nose pretty hard.
You can float the top shock mounts with the spacers, 1mm might be too much though. I haven't ever run into a pinched bearing in the diffs and in stock assembly the cams always seem to have some float in them, so no pinched bearings. Maybe make sure the cams are seated into the bulkheads properly with the notches. Your fix will work, just seems strange for this car.
You can float the top shock mounts with the spacers, 1mm might be too much though. I haven't ever run into a pinched bearing in the diffs and in stock assembly the cams always seem to have some float in them, so no pinched bearings. Maybe make sure the cams are seated into the bulkheads properly with the notches. Your fix will work, just seems strange for this car.