1LikesBMI Racing Discussions
12-01-2003, 05:11 PM
#451
Tech Adept
I belive Junior Norton finished 6th in Masters Stock TC "A". His car was awesome. I run for Warpspeed and finished 7th in the Stock "A". Good weekend for both BMI and Warpspeed. Lets keep the friction down. Both cars are great.
12-01-2003, 05:22 PM
#452
Great job to all in Cleveland! Rob, hope to see ya this weekend in Cinn. Again, great job. Here is my original setup posted earlier with a few minor adjustments. Scored a 3rd place finish after getting set a lap down (22.8 second on a 11 second track) in a tangle with a fellow driver. Ended up 1 second behind 2nd and 4 seconds behind first. Also pic is attached. Feel free to PM with questions or anything.
Front
70wt
#2 pistons
yellow springs
rear tower on the front on the inside hole
inner hole on the arm
losi 4 degree hubs
losi knuckles
f+0 block
-2 camber
zero tow in
camber link short and high
3mm of down travel
5mm of ride height
rear
50wt
#2 pistons
out on the tower and arm
Purple Springs
camber on the tower high and inside
losi 1/2 degree hubs (not flipped) with camber on the inside hole
hubs spaced in the middle
front block in the rear
R 2+0 block
same thing as above on droop
-2 camber
5mm of ride height
Jaco Plaid front, purple rear (2.28 preferred size)
100 tooth spur
Batteries forward
Losi Alfa with wing mounted center
Front
70wt
#2 pistons
yellow springs
rear tower on the front on the inside hole
inner hole on the arm
losi 4 degree hubs
losi knuckles
f+0 block
-2 camber
zero tow in
camber link short and high
3mm of down travel
5mm of ride height
rear
50wt
#2 pistons
out on the tower and arm
Purple Springs
camber on the tower high and inside
losi 1/2 degree hubs (not flipped) with camber on the inside hole
hubs spaced in the middle
front block in the rear
R 2+0 block
same thing as above on droop
-2 camber
5mm of ride height
Jaco Plaid front, purple rear (2.28 preferred size)
100 tooth spur
Batteries forward
Losi Alfa with wing mounted center
Last edited by jrighter; 12-01-2003 at 07:15 PM.
12-01-2003, 05:45 PM
#454
Thanks! I'm pretty anal about wiring. Usually I crack open my cases and make them the perfect length but the Quantum Comp 2 is very hard to open! Here's another pic. 
Last edited by jrighter; 12-01-2003 at 07:15 PM.
12-01-2003, 05:53 PM
#455
Oh heck... another
Last edited by jrighter; 12-01-2003 at 07:16 PM.
12-01-2003, 06:33 PM
#456
Originally posted by jrighter
Great job to all in Cleveland! Rob, hope to see ya this weekend in Cinn. Again, great job. Here is my original setup posted earlier with a few minor adjustments. Scored a 3rd place finish after getting set a lap down (22.8 second on a 11 second track) in a tangle with a fellow driver. Ended up 1 second behind 2nd and 4 seconds behind first. Also pic is attached. Feel free to PM with questions or anything.
Front
70wt
#2 pistons
yellow springs
rear tower on the front on the inside hole
inner hole on the arm
losi 4 degree hubs
losi knuckles
f+0 block
-2 camber
zero tow in
camber link short and high
3mm of down travel
5mm of ride height
rear
50wt
#2 pistons
out on the tower and arm
Purple Springs
camber on the tower high and inside
losi 1/2 degree hubs (not flipped) with camber on the inside hole
hubs spaced in the middle
front block in the rear
R 2+0 block
same thing as above on droop
-2 camber
5mm of ride height
Jaco Plaid front, purple rear (2.28 preferred size)
100 tooth spur
Batteries forward
Losi Alfa with wing mounted center
Great job to all in Cleveland! Rob, hope to see ya this weekend in Cinn. Again, great job. Here is my original setup posted earlier with a few minor adjustments. Scored a 3rd place finish after getting set a lap down (22.8 second on a 11 second track) in a tangle with a fellow driver. Ended up 1 second behind 2nd and 4 seconds behind first. Also pic is attached. Feel free to PM with questions or anything.
Front
70wt
#2 pistons
yellow springs
rear tower on the front on the inside hole
inner hole on the arm
losi 4 degree hubs
losi knuckles
f+0 block
-2 camber
zero tow in
camber link short and high
3mm of down travel
5mm of ride height
rear
50wt
#2 pistons
out on the tower and arm
Purple Springs
camber on the tower high and inside
losi 1/2 degree hubs (not flipped) with camber on the inside hole
hubs spaced in the middle
front block in the rear
R 2+0 block
same thing as above on droop
-2 camber
5mm of ride height
Jaco Plaid front, purple rear (2.28 preferred size)
100 tooth spur
Batteries forward
Losi Alfa with wing mounted center
12-01-2003, 06:37 PM
#457
12-01-2003, 06:46 PM
#458
Jbrake, just sent you a PM.
12-01-2003, 07:52 PM
#459
Jason, you make the posts longer also??
[QUOTE]Originally posted by NitroJohnnyD
[B]BMI makes an optional battery mount to direct screw your battery hold down in place. This is the method I use.
[QUOTE]Originally posted by NitroJohnnyD
[B]BMI makes an optional battery mount to direct screw your battery hold down in place. This is the method I use.
Last edited by jrighter; 12-01-2003 at 08:04 PM.
12-01-2003, 07:56 PM
#460
how do u like the quantum comp2??
12-01-2003, 08:02 PM
#461
It's waterproof, what more could you want? LOL.. It doesn't seem a whole world of difference from the old Quantum Comp. I can tell it is smoother. Still has the punch on the bottom but is smoother all around if that makes any sense.
12-01-2003, 08:14 PM
#462
Tech Legend
iTrader: (51)
Join Date: Sep 2001
Location: Castle Mamba Max Pro. Feel its power!!!!!!!!!!
Posts: 21,220
Trader Rating: 51 (100%+)
Very nice looking car. 
12-01-2003, 08:22 PM
#463
Thanks!
