Tamiya TRF415
Tech Fanatic
iTrader: (1)
I LIKE GOOOOLLLLLDDDD!!!!
Tech Master
iTrader: (5)
i have a trf415 i want to convert it to a 415msx i will buy a conversion kit of msx or first ms convertion kit will i use?
Originally Posted by RMF-888
i have a trf415 i want to convert it to a 415msx i will buy a conversion kit of msx or first ms convertion kit will i use?
Tech Master
Originally Posted by Rick Hohwart
Thanks! And word was the gold car was going to be a production car.
Any word, that Tamiya will be coming a new more updated 415??
Tech Elite
iTrader: (5)
Originally Posted by RMF-888
i have a trf415 i want to convert it to a 415msx i will buy a conversion kit of msx or first ms convertion kit will i use?
Tech Master
iTrader: (5)
Originally Posted by JRRobiso
BOK! Kamusta. You'll need the TRF415 MS Upgrade Chassis Conversion Kit.
Tech Regular
iTrader: (4)
Originally Posted by RMF-888
ok lng bok.so i must upgrade it 1st to a MS before MSX?
Hope this helps.
Originally Posted by RMF-888
ok lng bok.so i must upgrade it 1st to a MS before MSX?
1. light weight rev arms & uprights (F/R)
2. titanium susp shafts
3. titanium shock/damper shafts
4. 5 x 1.9mm bearing spacers for the uprights (F/R)
5. 2.5mm MSX bottom deck (415 = 3.0mm)
6. TRF Special edition dampers (blue)
7. rear bulkhead centerpost (not available as option part)
8. 5mm wheelhubs
9. TRF415 Aluminum Diff outdrive kit
10. 3x10mm Turnbuckle shaft (4pcs)
11. F/R low friction belts (white)
I think that's it (not sure though).......
All these parts I listed are available as option parts (hop-up parts) except the rear bulkhead center post.
I too had the std 415 then bought the MS upgrade kit & bought the other parts later. The center post I had to wait til ebay stores/Hongkong rc stores sold it seperately.
Tech Master
iTrader: (5)
thanx a lot guys for the info
Tech Fanatic
out of the loop
I have not touched my 415 in a while. I did put the Ta05 pulleys on it but never drove it. I keep reading about the new stering but is it ever going to be available to the public? I am going to need a new chassis before long anyway. I am still using the one from my original 415. Thats about all thats left. I am going to start heading to the track again and for some stupid reason i think i need the latest and greatest! My driving definately does not deserve it!
Sorry if this is a repeat question.
I am looking for alluminum front knuckles for my TRF415 MSX Refine 2. Does anyone know where I can find them?
Also does anyone know if there is a 6 degree castor block for it?
Thanks
I am looking for alluminum front knuckles for my TRF415 MSX Refine 2. Does anyone know where I can find them?
Also does anyone know if there is a 6 degree castor block for it?
Thanks
Tech Fanatic
Originally Posted by tcmerf
I have not touched my 415 in a while. I did put the Ta05 pulleys on it but never drove it. I keep reading about the new stering but is it ever going to be available to the public? I am going to need a new chassis before long anyway. I am still using the one from my original 415. Thats about all thats left. I am going to start heading to the track again and for some stupid reason i think i need the latest and greatest! My driving definately does not deserve it!
Tech Fanatic
Originally Posted by SlickZero.com
Sorry if this is a repeat question.
I am looking for alluminum front knuckles for my TRF415 MSX Refine 2. Does anyone know where I can find them?
Also does anyone know if there is a 6 degree castor block for it?
Thanks
I am looking for alluminum front knuckles for my TRF415 MSX Refine 2. Does anyone know where I can find them?
Also does anyone know if there is a 6 degree castor block for it?
Thanks
Originally Posted by Rick Draper
Square do alloy front knuckles for the msx.