1LikesXray T1FK05
04-19-2005, 10:34 AM
#1891
Originally posted by MartynD
hey now.... I was thinking about doing the exact same thing... same colour as well....
Anyways, did you notice any change in the fit of parts after getting that done Tim?
hey now.... I was thinking about doing the exact same thing... same colour as well....
Anyways, did you notice any change in the fit of parts after getting that done Tim?
Maritn
04-19-2005, 11:29 AM
#1892
Tech Regular
Haven't looked into it yet Martin, just an idea I was kicking around. I don't think it should be too tough to find someone able to do it... Though looking at how much dr was quoted.... ouch I won't be doing it at that price.
04-19-2005, 12:07 PM
#1893
Tech Regular
Martin,
Put the words: anodizing Toronto into Google, I found a few places right away.
I am not going to contact them just yet, but perhaps the next time I tear my car down I shall pay a visit to
http://www.progressiveanodizers.com/
Put the words: anodizing Toronto into Google, I found a few places right away.
I am not going to contact them just yet, but perhaps the next time I tear my car down I shall pay a visit to
http://www.progressiveanodizers.com/
04-19-2005, 12:10 PM
#1894
Tech Adept
You guys from T.O......Are you trying to make your car look like a tamiya car?.......
LOL,
Later,
Peter
LOL,
Later,
Peter
04-19-2005, 12:28 PM
#1895
Tech Regular
Of course Peter... if we can get it done in blooo
04-19-2005, 01:39 PM
#1896
Try looking into your local custom jewelry makers or motorcycle shops. A guy posted some good info about anodizing in the T1 thread.
04-19-2005, 02:14 PM
#1897
Originally posted by =MisFitz= NuKe
Ronnie...
You dork, I set a new track record...you could have just looked at my car...I WAS pitting right next to you.
-Mike
Ronnie...
You dork, I set a new track record...you could have just looked at my car...I WAS pitting right next to you.
-Mike
Yeah, I know I just wanted to see if there were any more setups out there. Latz
04-19-2005, 02:45 PM
#1898
I am thinking about putting a screw in the bumber top plate and screwing 20g of chassis weights into it upside down so they sit inside a hole cut out in the bumber, and 10g on each side in the rear just to get some weight on the car. How does that sound?
04-19-2005, 03:47 PM
#1899
i am new to the xray does anybody have a good setup for the fk05 on carpet
04-19-2005, 04:48 PM
#1900
Tech Regular
one came with the car
and I believe there are some in the XRay forums
and I believe there are some in the XRay forums
04-19-2005, 06:14 PM
#1901
Originally posted by duckman996
Isn't the servo side on a FK05 heavier or are you running 3700 packs? Am I reading this wrong
Just curious cause when I added weight I added more on the battery-side then I did on the electronics side to try to balance the car out (I run 3300 packs).
Isn't the servo side on a FK05 heavier or are you running 3700 packs? Am I reading this wrong
Just curious cause when I added weight I added more on the battery-side then I did on the electronics side to try to balance the car out (I run 3300 packs).
Region 2 19-Turn Results
1/TQ CRAIG XAVIER – Team Losi JRXS
2 BILLY SPENCE - Assoc TC4
3 MIKE DUNNIGAN - Assoc TC4
4 KEITH KOWAY - Xray FK05
5 CHRIS HAWKINS - Assoc TC4
6 TIM GITCHELL - Assoc TC4
7 GREG FANGONIL - Xray FK05
8 KOMKIT LITISARD - Xray FK05
9 MARK UNRATH - Corally RDX
10 JEFF CUFFS - Corally RDX
1/TQ CRAIG XAVIER – Team Losi JRXS
2 BILLY SPENCE - Assoc TC4
3 MIKE DUNNIGAN - Assoc TC4
4 KEITH KOWAY - Xray FK05
5 CHRIS HAWKINS - Assoc TC4
6 TIM GITCHELL - Assoc TC4
7 GREG FANGONIL - Xray FK05
8 KOMKIT LITISARD - Xray FK05
9 MARK UNRATH - Corally RDX
10 JEFF CUFFS - Corally RDX
04-20-2005, 06:14 AM
#1902
Originally posted by dr_hfuhuhurr
That rocks Tim! I have been e-mailing with an anodizer to get mine done in either Red or green.
Where did you have yours done? Cost? I was quoted $125 to get mine done. A bit pricy...but if it turns out half as good as yours...it's worth it!
Blake
That rocks Tim! I have been e-mailing with an anodizer to get mine done in either Red or green.
Where did you have yours done? Cost? I was quoted $125 to get mine done. A bit pricy...but if it turns out half as good as yours...it's worth it!
Blake
$90 and 3 FK05's will fit on the tray for that price.
It normally is $80, but they had to separate the different types of aluminum and do them separately.
Tim
04-20-2005, 07:32 AM
#1905
Originally posted by Isaac
If the electronics side is heavier then it is. The quarters came off right after the race anyway. I just did that to make weight plus two other '05s that made the "A" main (Greg and Komkit) put their weight in the same corner. My car was fine as I felt no weight differential while driving. Ignore the results of the Losi. If Craig had any car he would have been dialed anyway.
If the electronics side is heavier then it is. The quarters came off right after the race anyway. I just did that to make weight plus two other '05s that made the "A" main (Greg and Komkit) put their weight in the same corner. My car was fine as I felt no weight differential while driving. Ignore the results of the Losi. If Craig had any car he would have been dialed anyway.
http://www.pbase.com/steven13/image/41569638
