Xray T1
#2191
I got my stickers months ago too.
Can anyone tell me what the difference is between these two part numbers? 30 5100 and 30 5101? They are both listed as One-Way differentials. Any help is appreciated.
Can anyone tell me what the difference is between these two part numbers? 30 5100 and 30 5101? They are both listed as One-Way differentials. Any help is appreciated.
#2192
Suspended
Can someone give me the part number for the front one-way? I've been looking for it, but all I found was the components of the one-way but not the whole unit. And how many other spring sets does x-ray have for the shocks besides whats on the evo2?
Thanks,
Rick
Thanks,
Rick
#2193
Originally posted by Thistle
I got my stickers months ago too.
Can anyone tell me what the difference is between these two part numbers? 30 5100 and 30 5101? They are both listed as One-Way differentials. Any help is appreciated.
I got my stickers months ago too.
Can anyone tell me what the difference is between these two part numbers? 30 5100 and 30 5101? They are both listed as One-Way differentials. Any help is appreciated.
#2195
Tech Adept
well if i have the money after christmas i think ill get the xray. but i was wondering what servo and batterys u guys are running?after i get the car i wouldnt have much for a servo or batts. so it would probably be like $60 tops for the servo and ive been shoppin ebay for batts. so whats a good servo for $60 or less that i can use with my AM radio for now(FM later).
Thanks
Thanks
#2196
The airtonics 737 is probably one of the best servos you'll get for under $60 and its just under 60. I've run one in my sedan and it has good torque(57oz) and is relatively fast(.15sec). It's also high quality servo. Stomer has them for just under 60:
https://www.ssl-stormerhobbies.com/c...?pn=AIRS94737Z
https://www.ssl-stormerhobbies.com/c...?pn=AIRS94737Z
#2197
evo2 setup
anyone have a good setup for ozart carpet i plan on racing the silver city shootout in 2 weeks part of the triple crown race
most importantly the foams to use
most importantly the foams to use
#2198
Thanks RCInfinity.
#2199
Re: evo2 setup
Originally posted by kulasracing
anyone have a good setup for ozart carpet i plan on racing the silver city shootout in 2 weeks part of the triple crown race
most importantly the foams to use
anyone have a good setup for ozart carpet i plan on racing the silver city shootout in 2 weeks part of the triple crown race
most importantly the foams to use
#2200
Cleaning blue bearings
What is the quickest way to take the blue shields off the bearings? I have a couple that became somewhat gritty that I want to blast and re-lube. I can't see a notch or a c-clip and I don't want to muck it up. Is there a trick to do this? Thanks.
#2201
Tech Master
iTrader: (20)
kulasracing, anyone have a good setup for ozart carpet i plan on racing the silver city shootout in 2 weeks part of the triple crown race
#2202
elnitro: Iuse a magnifier light and a needle to remove the shields. Helps me see them better and then a bearing blaster to clean them.
#2203
Tech Initiate
This should ammuse a few.
elnitro, the best way to get the shields out is to put them in the car and use them, bingo!!
//Stu
elnitro, the best way to get the shields out is to put them in the car and use them, bingo!!
//Stu
#2204
Ragman
Ragman,
Actually you are not amusing. It just made you look like an idiot. This thread is a cool place to share tips and info on Xrays, please don't muck it up with your non-sense.
Actually you are not amusing. It just made you look like an idiot. This thread is a cool place to share tips and info on Xrays, please don't muck it up with your non-sense.
Last edited by elnitro; 12-26-2002 at 03:37 PM.