Hot Bodies Cyclone
06-26-2008, 07:41 PM
Airtronics 94360 high-speed digital servo
06-26-2008, 07:56 PM
Futaba BLS451, quiet, smooth and no glitching noise!
06-26-2008, 08:42 PM
New to the whole rubber tire on carpet thing, anyone have any good setups for rubber tire carpet, need to start practicing for IIC.
06-26-2008, 09:22 PM
The Futaba is in there now for it's smaller foot print.
06-26-2008, 10:04 PM
06-27-2008, 08:54 AM
06-27-2008, 10:41 AM
Tech Fanatic
iTrader: (14)
does anyone know where I can find purple screws?
06-27-2008, 10:45 AM
06-27-2008, 12:25 PM
06-27-2008, 01:44 PM
06-28-2008, 08:40 AM
Tech Rookie
Cyclone Tc top deck
just putting together a Cyclone TC on the setup board the chassis is nice and level, as soon as i fit the topdeck it pulls the bulkheads together and i can rock the car from side to side slacken the deck of and it lies flat.
anybody had the same prob wondered if i used a topdeck from wce would this cure the problem.
Cheers
Kev-h
anybody had the same prob wondered if i used a topdeck from wce would this cure the problem.
Cheers
Kev-h
06-28-2008, 08:50 AM
06-28-2008, 05:20 PM
06-29-2008, 11:35 AM
Hara Won in Euro Championship Round 4
06-30-2008, 08:17 AM
hi i have a hot bodies cyclone moor speed WCE and i run at wlrc race track . I was wondering if anywone could help me out please .I would like to know your setup at wlrc for this car
This is my setup :
108 spur and 35 pinion
3mm spacer between the upper bulkhead and the inner pivot for front
and 2mm between upper bulkhead and inner pivot for rear
5mm front ride height
5.5mm rear ride height
5.5mm droop front
5mm droop rear
standart suspension 2 holes ,1mm each ,40w oil standart spring gold rear silver front
camber 1.5
castor 4
wheelbase is standart
and for the "dive" and"squat" is: 1.5mm under the suspensionpivot block rear
and 2mm front suspension pivot block and 1mm under rear front suspemsion pivot block dodge stratus bodyshelle
for the toe angl because i dont have the proper tools to mesaure it there is 25mm difference between each palstic thing that screw themselves to the turnbuckles
4mm ackermann
and i think thats it
for the elctronics:
lrp5.5turn gearing 7.5 (108 spur 35 pinion)with novak GTB 1st brushless profile with gemini 2 transmitter with micro 41 mhz receiver and T2M diamond digital servo (0.12 @ 60 , 13 kg torque) and finally i have 1 pack of orion SHO 4200 batteries , + 1 pack of demon ep 4200 + 2 pack of LRP hv2 vtec 4200 bigmama
and i forgot to say that i never run there when there are races i only go weekdays to practice myself
Thanks alot if you guys could help me out
This is my setup :
108 spur and 35 pinion
3mm spacer between the upper bulkhead and the inner pivot for front
and 2mm between upper bulkhead and inner pivot for rear
5mm front ride height
5.5mm rear ride height
5.5mm droop front
5mm droop rear
standart suspension 2 holes ,1mm each ,40w oil standart spring gold rear silver front
camber 1.5
castor 4
wheelbase is standart
and for the "dive" and"squat" is: 1.5mm under the suspensionpivot block rear
and 2mm front suspension pivot block and 1mm under rear front suspemsion pivot block dodge stratus bodyshelle
for the toe angl because i dont have the proper tools to mesaure it there is 25mm difference between each palstic thing that screw themselves to the turnbuckles
4mm ackermann
and i think thats it
for the elctronics:
lrp5.5turn gearing 7.5 (108 spur 35 pinion)with novak GTB 1st brushless profile with gemini 2 transmitter with micro 41 mhz receiver and T2M diamond digital servo (0.12 @ 60 , 13 kg torque) and finally i have 1 pack of orion SHO 4200 batteries , + 1 pack of demon ep 4200 + 2 pack of LRP hv2 vtec 4200 bigmama
and i forgot to say that i never run there when there are races i only go weekdays to practice myself
Thanks alot if you guys could help me out