Tekno RC SCT410.3 Thread
|
|||
#2746
Tech Adept
I got the roller put together last night. I gotta say, I'm impressed with the quality of the plastic. At least as compared to my SCTE.
#2747
Honestly, I have a 6040 in one of my 8th scale buggies and it does great. No lag in time or lack of torque. This is just my experience. That servo is super quick too.
#2748
Tech Elite
iTrader: (152)
Anyone having an issue with the front bumper on this truck? Every time my son lands a little nose down the bumper pushes out from the chassis and then hangs down about 1/4 below the front of the chassis. It causes issues with handling once it happens for the rest of the run. There are not super hard hits causing this issue so any help would be great.
Thanks
Thanks
#2749
Anyone having an issue with the front bumper on this truck? Every time my son lands a little nose down the bumper pushes out from the chassis and then hangs down about 1/4 below the front of the chassis. It causes issues with handling once it happens for the rest of the run. There are not super hard hits causing this issue so any help would be great.
Thanks
Thanks
#2750
Tech Initiate
Sct410.3 to buggy
Hello, I know that it is possible to convert the sct410.3 to a buggy but I'm not sure what I'd need complete the conversion. If someone could help it would be appreciated.
Thanks Alex
Thanks Alex
#2751
Tech Elite
iTrader: (152)
No... Not exactly..
Are you saying that the bumper has ripped the screw off of the front hingepin block? If the screw hole has stripped out you could CA it in place in the meantime. Eventually I would say you should upgrade to the aluminum A bock. It's more durable in a crash and won't strip out.
The issue is the bumper must be flexing enough to allow it to drop down below the chassis plate but it is not pulling the screw out of the front bulk head. The are where the bumper gets sand-wedged between the bulkhead and chassis is what is coming out and dropping below the chassis.
I have to dig the dirt out of the front screw hole, remove screw still that is still holding bumper to bulkhead, loosen screws that hold the bulkhead to chassis so I can get bumper back in place and then screw it all back together.
This is happening almost every run.
Again, not down on the truck, it works great, just need to get this issue resolved.
See Photos Below:
#2754
I had the same problem but I use De racing skid plates for the rear. So i took a "rear" skid plate put it in the front and trimmed a little off so it would line up with the holes and for some reason I didn't have any more issues but def get the aluminum "A block" and don't over tighten the screw.
#2755
Tech Adept
I finished my kit yesterday. Very happy with how everything went together. The only issue I would like to address is on the steering. There is a little up down play in the bell cranks. Not much but enough to notice. I could not find a suitable shim in my RC parts bin to remove the play. Anyone have any recommendations?
#2756
Thanks for the response and I want to say the truck is great. My son won the A-Main with it last Friday night.
The issue is the bumper must be flexing enough to allow it to drop down below the chassis plate but it is not pulling the screw out of the front bulk head. The are where the bumper gets sand-wedged between the bulkhead and chassis is what is coming out and dropping below the chassis.
I have to dig the dirt out of the front screw hole, remove screw still that is still holding bumper to bulkhead, loosen screws that hold the bulkhead to chassis so I can get bumper back in place and then screw it all back together.
This is happening almost every run.
Again, not down on the truck, it works great, just need to get this issue resolved.
See Photos Below:
The issue is the bumper must be flexing enough to allow it to drop down below the chassis plate but it is not pulling the screw out of the front bulk head. The are where the bumper gets sand-wedged between the bulkhead and chassis is what is coming out and dropping below the chassis.
I have to dig the dirt out of the front screw hole, remove screw still that is still holding bumper to bulkhead, loosen screws that hold the bulkhead to chassis so I can get bumper back in place and then screw it all back together.
This is happening almost every run.
Again, not down on the truck, it works great, just need to get this issue resolved.
See Photos Below:
#2757
I finished my kit yesterday. Very happy with how everything went together. The only issue I would like to address is on the steering. There is a little up down play in the bell cranks. Not much but enough to notice. I could not find a suitable shim in my RC parts bin to remove the play. Anyone have any recommendations?
#2758
Tech Adept