Tamiya TA05 Touring Sedan
#9346
94,
Thanks for the info. Hard to naviagte the sea of parts on the Tamiya site.
Thanks for the info. Hard to naviagte the sea of parts on the Tamiya site.
#9347
Or just some m3 sized standard washers should be good enough for a 1mm shim.
#9348
Tech Elite
iTrader: (24)
In the Standard 05 suspension there are only 1 and 2 degree rear hubs. But you can cancel the toe with the toe blocks.
As far as I know there are no different length arms for the standard suspenion. You can use the short arms designed for the TA04SS...but they are short as in wheelbase not car width.
There are varying lengths of arms for the lightweight suspension. I'm not sure exactly the difference but it's between 1-2mm per arm.
And yes, the hard rear hub on the standard suspenion is 1 degree.
As far as I know there are no different length arms for the standard suspenion. You can use the short arms designed for the TA04SS...but they are short as in wheelbase not car width.
There are varying lengths of arms for the lightweight suspension. I'm not sure exactly the difference but it's between 1-2mm per arm.
And yes, the hard rear hub on the standard suspenion is 1 degree.
I am running from front to back 1D ,D bridge, 1B, 1D
With the hard 2 Degree uprights.
This setup makes the car very wide, so you need to run the 5mm hexes
#9349
Differant colour, differant thickness.1mm red0.5mm blue(unless its the other way around)check it athttp://www.tamiyausa.com/product/rcpss.php
#9350
http://www.tamiyausa.com/product/ite...oduct-id=53646
http://www.tamiyausa.com/product/ite...oduct-id=53647
#9351
Tech Apprentice
Hi,
No, just different colours, both packs contains two sets (4 each) of 1mm and .5mm. Red seems harder to find tho.
No, just different colours, both packs contains two sets (4 each) of 1mm and .5mm. Red seems harder to find tho.
#9353
Tech Champion
iTrader: (108)
No, the stocks are 2 and the hards are 1.
http://www.speedtechrc.com/store/ebp...id=461&id=1710
http://www.speedtechrc.com/store/ebp...id=461&id=1710
I have always been under the impression that the non- 2 degree rear uprights were 0 degrees not 1, but I can always be wrong
I am running from front to back 1D ,D bridge, 1B, 1D
With the hard 2 Degree uprights.
This setup makes the car very wide, so you need to run the 5mm hexes
I am running from front to back 1D ,D bridge, 1B, 1D
With the hard 2 Degree uprights.
This setup makes the car very wide, so you need to run the 5mm hexes
#9354
Does anyone know which roar legal lipo other than the orion fits in the stock tub chassis without modification?
#9355
TAO5 ready lipo's
If you are looking for LIPO batteries that fit ito the grooves of the chassis like a 6 cell pack, the Oroin 3200 fits in the stock battery slot.
I beleive the Orion 3600 may as well as both have the same general form factor as well as the feet on the bottom that allow it to fit into the battery slots.
I beleive the Orion 3600 may as well as both have the same general form factor as well as the feet on the bottom that allow it to fit into the battery slots.
#9357
Tech Adept
iTrader: (5)
#9358
I got the Orion 3200. Want a bigger one.
Does the Reedy 5000 fits?
Their price is pretty good. Under $100
Does the Reedy 5000 fits?
Their price is pretty good. Under $100
#9359
http://www.acerracing.com/products/3...ls-773-66.html
#9360
on my 05r i put 3mm shims on the axle with 5mm clamping hubs and still cant get 28mm foams to clear the ballcup on the steering knuckle. the tires are the old style rims(parma)not the newer larger style rims. any sugestions besides some creative grinding?